20 Most Recent 2006 Lexus Gs 300 - Page 6 Questions & Answers

just remove the air intake box. then remove the throttle body , which should consist of two connectors and two coolant hoses and the throttle plate cable. all very easily accessible. once you have the cable, connectors and coolant hoses dissconnected, there is one nut at the bottom of the throttle body and two long screws at the top. slide the throttle body of the rod at the bottom. then remove the three bolt that hold on the big rubber gasket. now disconnect the three coils (which the little clips will break, but dont worry. after removing the wires and coil IMPORTANT!!! blow out all the debris in the alley due to it might fall in the engine while removing the spark plugs. perform service and dont worry if you mix up the coils it wont matter. just make sure the the wire go in the rght spots. then assemble together.

Hi if the drivers window works then this suggests the fuses are ok.

now the problem you are having is going to be with the switches that control the windows, if the drivers side switch is the same as the passenger then what you can do is pry the drivers side one up and pull it out and swap it with the passenger one, doing this will then tell you if the switch is at fault or the motor if it works then you need to replace the switch if it dont work then you need to replace the motor.
let me know if you have electric windows in the back as this could be a fuse, one thing you can do is look in the fuse box and on the back of the fuse box lid it should tell you what each fuse is for and then just pull the one for rear windows, if its not written on the back of fuse box cover than it will be written in the owners handbook that you get when the car is new usually kept in glove box or under seat.

let me know how you get on or if you need further assistance ok

Did you try with the key? The keyhole is in the top left corner in the trunk by license plate (opposite to the camera lens).
Also, make sure the valet button in the glove compartment is released (or pressed)

Check your brake fluid reservoir if you are low. Other than that, the only parts with fluid are the shocks.

you gotta remove it by hand. it shouldn't be to tight. just unscrew it like you'd unscrew a screw. when yoiu put the new one back in get a little of the new oil and put it on the gasket. get it wet but not too wet. that'll help it seal and will make it easier when yopu try to replace it again

WITH IGNITION SWITCH OFF PRESS AND HOLD BUTTON ON THE TRIP ODOMETER THEN .SWITCH IGNITION ON WITH ENGINE OFF.CONTINUE TO HOLD BUTTON UNTIL MAINTANANCE REQD LAMP EXTINGUISHES RESETTING IS DONE.

The 2006 has an engine imobiliser in the ignition and micro chip in the key fob. There could be a low battery in your key fob. Take your spare key or your good key and hold it right beside the push button when cranking. See if that allows the engine to fire and remain on. If so replace the battery inside the fob. You can do this by pulling the glove box (silver) key from the end of the fob and inserting the tip of the key into its slot sideways to pop open the **** shell housing and expose the internal battery.
Post back with results.

yes.

the connection for the mirror is located behind the door trim panel. you must remove the door trim panel to accdess the connection.

You have to reset the windows and sunroof after you change the battery. For windows open the driver half way and close the window up and hold the up switch for few seconds. If that don't work open the rear window from rear switch and that should work.
For moon roof open the moon roof and keep the hold the open button pressed for 10 seconds. Then close the moon roof and hold the close button pressed for 10 seconds

first i would check under hood passenger side firewall, for a small tube some will L down. run a wire or small screwdriver in the hole. could be clogged. this is a drain for the a/c and if stopped up it will back up into car.

check wiring or proceed to the mechanic for reset

replacing one is ok but replace two minimum to create even wear on the tires

That would be a dealer only tool that would be specific to your car, there are generic types that you can buy that hold the engine from the top and sit on the strut towers and are probably available through OTC, or Snap-on, or mac tools, but are very pricy. Another solution would be to make your own support to run across the strut towers and chain the engine up or use a cherry picker.

there is a cancel button in the glove box for the trunk lid. check and make sure its not activated.

there is a cancel button in the glove box, check this first to make sure its not activated.

push down on trunk slightly then unlock, when open lubricate locking mechanism, if rear seat folds check for Florissant handle to open