20 Most Recent 1991 Jeep Wrangler Questions & Answers


Spray some starting fluid into the throttle body. If it starts then you have a fuel problem. If it does not, then check to see if you have spark to the plugs.

1991 Jeep... | Answered on Mar 09, 2019


Check the wiring going to the coil. If you installed an alarm on that vehicle disconnect the main power wire to the alarm to disable the ignition kill circuit. Locate the ignition relay located on the drivers side fender wall or in the power distribution box under the hood and test it. finally, there is a fuse on the interior fuse panel that will give you this condition. I do not have the exact location so check all fuses in the panel and replace any blown fuses.

1991 Jeep... | Answered on Mar 02, 2019


see rthe link and go to bottom of the page..
Jeep Workshop Manuals
mjk-hd2gaexkk5xamahzjtbr5cso-4-0.jpg

1991 Jeep... | Answered on Nov 07, 2017


hi there.
not sure if this link will help you out but have a look.
1991 Jeep Wrangler stall and die Google Search

1991 Jeep... | Answered on Nov 06, 2017

1991 Jeep... | Posted on Oct 09, 2017 | Be the first to answer


Check out ebay and see if you can get the part there. U can also check your local junkie for a good, used working part.

1991 Jeep... | Answered on Mar 22, 2017


If, when you turn on the ignition, you do not see the check engine light come on in the dash then your ecu is in need of repair. The ecu has to energize the relays that send power to the fuel pump and injectors. Until that check engine light comes on, no power will be sent to the relays, thus no start. There are a lot of posts on this site about this, called the delayed start check engine light problem.

1991 Jeep... | Answered on Mar 06, 2017

1991 Jeep... | Posted on Mar 06, 2017 | Be the first to answer


what about it ?

1991 Jeep... | Answered on Jan 05, 2017


Can't push clutch pedal in - JeepForum.com

www.jeepforum.com > ... > TJ Wrangler Technical Forum

Dec 11, 2010 - 7 posts - ‎3 authors
Driving home last night and the clutch pedal falls to the floor. ... Forums > TJWrangler Technical Forum > Can't push clutch pedal in ... Comes back up but then Ican't push it back in at all, even trying to stand on it, won't budge. Clutch locking up?
10 posts
Jul 30, 2011
Clutch Pedal Frozen Need tech help
10 posts
Sep 8, 2009
Clutch pedal stuck in the up position.
6 posts
Jul 26, 2009
Any more to clutch adjustment?
10 posts
Nov 28, 2008
More results from www.jeepforum.com

1998 Wrangler Sahara - Won't go into gear! Help please! - Jeep ...

www.wranglerforum.com/.../1998-wrangler-sahara-wont-go-into-gear-h...

Oct 5, 2010 - 22 posts - ‎7 authors
With the engine off, i can push the clutch in, and shift through all the gears ... to move - the clutch isn't disengaged even with the pedal fully depressed. .... Also, trying to bleed the system, can't find the bleeder screw. .... 1991 Jeep Wrangler Stuck In Gear? jeffasel, YJ Tech Forum, 5, 10-19-2010 09:42 AM. Getting difficult to push clutch pedal down, HELP
20 posts
Jun 17, 2011
How to bleed my clutch Be spacific.
11 posts
Feb 26, 2011
Clutch Problem?
30 posts
Jun 22, 2010
My Clutch Problems and How I Resolved Them
8 posts
Jan 28, 2009
More results from www.wranglerforum.com

1991 Jeep... | Answered on Jan 14, 2016


I have the same problem ??? Did you ever figure it out ???
stever@hsmpackaging.com

1991 Jeep... | Answered on Dec 15, 2015


http://serpentinebelthq.com/1991-jeep-wrangler-yj-4-0l-serpentine-belt-diagram/ her is a link for you to a diagram. I hope this helps

1991 Jeep... | Answered on Jul 12, 2015


hi see if there is a switch behind the brake peddle,undo one of the connectors,then switch ignition on and see if the brake lights have gone out,if so replace falty switch.
good luck hope this was some help,PH.

1991 Jeep... | Answered on May 05, 2015


what year chevy,
carb or EFI?

1991 Jeep... | Answered on Apr 12, 2015


steering linkage is binding,was there an extension provided with the kit?

1991 Jeep... | Answered on Apr 03, 2015


2 reason,
the pump handle at the station is bad. (move to different island or pump)
or
your car. so if all stations are bad then it is your car !
(why not say so)
Car: (all)
so what is bad,, well that is EVAP system failure.
vent hose pinched or blocked at filler neck see that side hose on filler pipe?
and on newer cars. there is and electric valve that opens key off.
91 wrangler is old car.
no valve.
its a hose problem. rare to have this hose block, very rare, unless
collision damage kicked it.
but it is an old car, maybe the ethanol is killing the insides of it.
E10 fuel here, in USA,

1991 Jeep... | Answered on Mar 24, 2015


There should be a sticker in the engine compartment that shows the routing and you should be able to hold the tensioner back with a 3/8's ratchet with a long handle.

1991 Jeep... | Answered on Jan 26, 2015


where is it, on a 2.5L I4 jeep. 1991. ok. first ever post with engine size.
bravo that. amazing....
the FSM covers this. factory service manual;,.
ok, i see you are reading books or web sites that have generic tuneup information, not relate to real jeeps, yes?
or bob with a toyota told me to change it out? yes?

Guess what?, there IS NONE.
it only has and ORIFICE.
and sure it can clog, and does, in fact i drove for 500,000 miles
in 3 jeeps. and cleaned it vast times.
on one car , the grommet got old and it the orifice collapsed.
and i had to buy a new one from jeep.
see word FIXED below.?
when it clogges, the engine leaks oil
and the oil pukes (backups) and dumps oil on the air cleaner.
there is no PCV valve, on this engine. but that dont mean its service free.






1d4c96fd-4de0-4f15-a00c-001f18919664.jpg

1991 Jeep... | Answered on Sep 30, 2014


It is in the main fuse panel ?? are you sure it is a fuse problem not the reverse switch itself ? or one of the bulbs out ?

1991 Jeep... | Answered on Sep 27, 2014


really depending on how far you want to go as you will need a vrs kit that will be over a hundred and then it all depends on damage done , to hard to be accurate with out the head being removed, crack tested valve seats coupled , surface grind. bit of specialist machineing involved . and other things cropped up like valve stem wear etc . hope that gives you a bit more of a idea

1991 Jeep... | Answered on Sep 19, 2014

Not finding what you are looking for?
1991 Jeep Wrangler Logo

481 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1995 Jeep Wrangler
1995 Jeep Wrangler

625 Questions

1997 Jeep Wrangler
1997 Jeep Wrangler

538 Questions

1998 Jeep Wrangler
1998 Jeep Wrangler

522 Questions

1999 Jeep Wrangler
1999 Jeep Wrangler

455 Questions

1992 Jeep Wrangler
1992 Jeep Wrangler

334 Questions

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Wrangler Jeep

  • Wrangler Jeep

Most Popular Question

diagnostic connector located 1991 jeep

  • Cars & Trucks
Loading...