20 Most Recent 2006 Hyundai Sonata - Page 6 Questions & Answers

Did you change the Idle air motor as well? It is sometimes possible to clean these.

Most window switches will pop out of the bezel assembly with a gentle pry using a suitable tool. Disconnect the plug on the old switch and reinstall on the new one

If they don't come on, Look at the fuses. Pull them out and look. This takes care of corrosion problems. If you only have low or high beams. Replace the turn signal switch. The only light relay is the turn signal switch.

Read the code, replace the part, No diagnostics done. Check the sensor, check wiring, and check the PCM/TCM. Most likely, you replaced a good part. Your mechanic should have told you if there was a PCM/TCM upgrade.

Hi Lee
Could be open contacts on the Relay.
A Relay is simply a set of contacts actuated by an electromagnet coil.
A relay can click but it doesn't mean the internal contacts are closing.
Is there one relay for left side and another for right?

Use a 12v test light or Multimeter on 12 volts to trace the power.


Look at the connectors on the base of the Relay.
Get a pin out diagram of that relay of the Internet.
2 pins for actuation. Gnd & +12v.
2 Switch contact pins.
Short the "contacts" switch pins together to simulate Relay closing its Contacts.
Is there Battery 12v at one of the relay socket "contacts" pins?

Use a jumper lead from Battery + to that relay wire.

Good luck

If you are looking to open the hood of an Infiniti QX56, look for a lever somewhere on the side of the steering wheel or by the driver's side door. --------------------------------------------------------------------------------Digiprog3

hood latch malfunction, may have to hit it a few times might work or may need to get under front of car locate hood cable and pull it down should open

They will always give you that reply but the staff telling you that would not know because most likely they did not watch your car being worked on by the guy handling the tire fitting on your car. Just removing and refitting the wheels could not result in either of those problems. Nor could doing a wheel alignment if you had that done as the wheels are on the car for that to be done. The only damage they could normally have done is to the underside of the car by either someone driving your car or when the vehicle was being put on the lift. I would get the car up on a lift and inspect the underside for damage. I would also jack up the car and remove each of the front wheels in turn for a visual inspection and see if there is any sign of damage to any components. It is unlikely you will find anything though. Both of the problems you have are electrical as both the speedo and gas gauges are operated via electronic sender units and wiring from the sender units into the dash gauge assembly.

There are 2 possible engines for your car. The diagram for each is listed below. Best of luck!
Greg

2006 Sonata 2.4L Serpentine Routing:



2006 Sonata 3.3L Serpentine Routing:

All this means is that your car will not pass an OBD 2 emissions test.
P-powertrain
1-MFG: manufacturer specific
5- vehicle speed control and idle control system
07- Hyundai 07 fault code.

The knock sensor i think is on the back of the engine block,Has a 10mm bolt holding it on.

I believe I check the oil before I moved the car.

Dear kaydynandtri, If you have the owner's manual find the power window relay. They are usually located in the fuse box. Check to see if there is another relay that matches that one and switch places with them. If the windows work or the accessory the relay came from does not the relay is bad. If this does not work I would replace the driver's door power window switch. I have also seen the wire break on older cars where it goes into front of driver's door.

I have a 2006 Hyundai Sonata GLS V6. I was told there's 2 on my vehicle. Is that true? If so does anyone know where they both are? Thanks guys!

This is the trouble code definition....gives you a starting point!

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

need to resubmit your question ===why would you need to replace a fuse /relay unit or all fuses and on what yr ,make,and model