2001 Hyundai Accent - Answered Questions & Fixed issues

The torque specification for the rocker shafts on the 2001 Hyundai Accent with the 1.5L single overhead cam engine is 18-20 lb-ft. The proper torque sequence is as follows:

1. Tighten the bolts to 8 lb-ft in a crosswise pattern.
2. Increase the torque to 15 lb-ft, again in a crosswise pattern.
3. Finally, tighten the bolts to the full torque of 18-20 lb-ft, again in a crosswise pattern.

Make sure to use a torque wrench and follow the sequence carefully to ensure proper tightening and prevent damage.

Maybe the coil pack module that the coil packs sit on is bad if it's like a GM.

Changing the coil packs alone won't always solve the problem.

sounds like you have a blown fuse to your cigarette lighter. look in the fuse box for a blown fuse.

Click on the images Rusty Weeks. https://www.google.com/search?q=2001+hyundai+accent+cam+cap+bolt+torque&rlz=1C1QJDB_enCA643CA644&sxsrf=APq-WBviGncM0J5PLYMinrCZpHab3F9gRg:1646440009074&source=lnms&tbm=isch&sa=X&ved=2ahUKEwiJwon_2q32AhUJmHIEHV2pAPwQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..

The good news is you can use the same data the dealers use the bad news is, it is not free. Hyundai Service Website (hyundaitechinfo.com)

Learn how to use YouTube. Go to the YouTube web site, and in the search box at the top of the screen type "2001 hyundai accent map sensor". Look at the videos it brings up -- it may not show exactly a 2001 Accent, but you should be able to find an engine that looks like yours and see where the MAP Sensor is.

My answer is a bad wheel bearing I explain it in the comment on the prior gentleman's answering of the question I can repeat it if you need me to but I think it's spelled out pretty well in the comment section of the first answer good day.

Most of the time the linkage got loose.

there are usually three beltsone for power steering, one for the alternator and one for the aircondition.the names / sizes depend on the engine 1.5 1.6 2 litre....

Please refer to the provided links. https://www.autocodes.com/p0456_hyundai.html https://www.autocodes.com/p0442_hyundai.html You have a leak in the fuel system or a defective fuel tank and or evap pump or pressure sensor or both

Take it to a qualified repair shop . One that has a professional scanner an know's how to use it , an has factory sevice repair information and the knowledge to diagnose . Or go on youtube an search the code's an learn how to test .

i think you need to go back to basics.if here is no obd fault codes in the system to give you a clue. then use a multimeter and have a good look at the wiring for corroded connectors etc. including the fuel pump?

no you need the appropiate code generator ,best advise is to go to the dealer .

Need to go to the dealer with your VIN number and proof of ownership if radio is factory installed. If aftermarket you need to contact the manufacturer.

Did the battery explode, or leak, do you have power anywhere else? If so you need a new battery. And yes there are other fuses under the hood, normally next to the inside of the fenders.

10 amp fuse #26 powers illumination. See diagrams below.

I suspect the pump is inside the reservoir. The link is for a Hyundai Elantra (2001-2006) and shows how to get to it for this model. Hope this helps! How To Install Replace Windshield Washer Pump Hyundai Elantra 01 06 1AAuto...

No light no work. The first thing I would check is switch. Remove switch place probes from a multimeter in switch set multimeter to continuity activate switch listening a tone.if tone is present switch is good

Sounds like a coolant sensor problem. It signals the ECU for open loop, cold start rich, high idle, until warm up is reached.

Evaporator vent silenoid at rear by gas tank is most likely stopped up. Is the check engine light on? If so, take to Auto Zone and get them to scan it for free. Get codes only and post them.