Need instructions to replace 1993 Toyota Camry Timing Belt
Hi Kmcarroll77
TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry
Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to
specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean
and rotates smoothly. 2.Install No. 1 idler pulley and tension spring
(if removed). Pry No. 1 idler pulley away from timing belt area as far
as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler
pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt,
rotate crankshaft so timing mark on crankshaft sprocket aligns with
timing mark on oil pump housing. See. This will position keyway in
crankshaft sprocket at 12 o'clock position.
CAUTION:If reusing timing belt, ensure reference marks on timing belt
align with reference marks placed on crankshaft and camshaft sprockets.
Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing
belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and
then No. 2 idler pulley in sequence. 5.Install timing belt guide with
cupped side away from crankshaft sprocket and flat side toward timing
belt. Install No. 1 timing belt cover and new gasket. 6.Align
crankshaft pulley key groove with key in crankshaft. Install crankshaft
pulley. Install and tighten crankshaft pulley bolt to specification.
7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on
compression stroke. Ensure timing mark on crankshaft pulley aligns with
"0" mark on No. 1 timing belt cover. If reusing timing belt, ensure
reference mark on timing belt aligns with upper edge of No. 1 timing
belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with
alignment mark on camshaft bearing cap. See Fig. 2 . Install timing
belt on camshaft sprocket. If reusing timing belt, ensure reference
mark on timing belt aligns with the reference mark on camshaft
sprocket. Ensure tension exists on timing belt between the crankshaft
and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2
full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on
crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and
hole in camshaft sprocket aligns with alignment mark on camshaft
bearing cap. See Fig. 2 . If timing marks are not aligned, remove
timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8
revolutions and align crankshaft pulley "0" mark with 45-degree Before
Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 .
12.Tighten No. 1 idler pulley bolt to specification. See TORQUE
SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install
and tighten spark plugs to specification. 13.To install remaining
components, reverse removal procedure. Install all bolts/nuts on right
(timing belt side) engine mount before tightening to specification.
14.On Camry, when installing control rod and bracket on strut tower and
right (timing belt side engine mount, tighten bolts to specification in
sequence. See Fig. 6 . On MR2, tighten engine
Hope this helps, don't forget to rate.
Lazaruselite
Posted on Feb 25, 2009
whats the function of a EFI fuse
It supplies the EFI Main relay, which in turn powers the fuel pump, ignition switch, and starter relay. In addition it powers the ECM computer, so that if you wish to clear a trouble code from there, you pull the EFI fuse for 30 sec. See here p177
http://www.turboninjas.com/camry/eg1.pdf
Posted on Jan 09, 2013
My 1993 model Toyota Camry refuses to enter into drive (D). It only enter D2 and L. Though i moves in the forward direction, it drags and causes overheating with water spurting out of the radiator. The OD Off/On light blinks continuously as well.
The blinking O/D light has the same function as the Check Engine light, but for the transmission. So stored in the car's computer is a trouble code which will allow you to localize the transmission problem, and the first thing is to get that read out. You can do this yourself by bridging terminals TE1 and E1 under the hood, see here, p44 and p80
http://www.turboninjas.com/camry/ax1.pdf
Then look up the cause in this document. Most such problems are best fixed on a hoist, so you might want to take it to a transmission shop.
Posted on Feb 20, 2013
Would like to know if there's a website I can go to, to get programming instructions at no cost.
Please try this. Toyota - 4Runner . org Forum > Toyota 4Runner Forum > 3rd gen T4Rs > Programming Instructions for keyless entry remote? Pages (2): [1] 2 » Last Thread Next Thread Author Thread rav04 Junior Member Registered: Nov 2004 Location: Canada Posts: 6 Programming Instructions for keyless entry remote? I have a 1999 4runner LTD, can anyone provide me with the instructions to program my keyless entry remote? Thanks __________________ RAV Report this post to a moderator | IP: Logged 12-31-2004 02:11 AM NoliWan Member Registered: Dec 2004 Location: San Jose, CA Posts: 34 Hey RAV, I got your PM-- Here are the instructions for programming the 99-02 4Runner Keyless Entry factory remotes: 1. Start with the following conditions: you are in the vehicle a. Key is out of the ignition b. Drive door is open ( all other doors are closed) c. Driver door is unlocked (other door locks don't matter) 2. Insert the key into the ignition (don't turn it) and pull it out. 3. Perform these steps within 40 seconds: a. Cycle the power locks 5 times. Use an even pace and try to go relatively fast. b. Close, then open the drivers door. 4. Perform these steps within 40 seconds: a. Cycle the power locks 5 times (same as before). b. Turn the ignition to ON then back to OFF. c. Turn the ignition to ON then back to OFF. d. Remove the key from the ignition. 5. Within 3 seconds, the power door locks should cycle (automatically) indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point. 6. Perform these steps within 40 seconds: a. Press the LOCK and UNLOCK buttons on the transmitter simultaneously for 1 second. b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle ( LOCK then UNLOCK) once-- indicating successful programming. If the door locks don't cycle, or cycle twice. Repeat steps 6a and 6b--this remote has not been accepted. c. Repeat steps 6a and 6b for EACH transmitter that will operate the vehicle. Including any old transmitters. 7. Close the driver door. Hope this helps you, it did me greatly-- Good luck, NoliWan __________________ 2000 SR5 4Runner 4WD ____________________ TRD 2nd Gen. Supercharger / TRD Headers / TRD Cat Back Exhaust / TRD Trans. Cooler / TRD Performance Wheels / TRD Boost Gauge / URD Fuel Kit Upgrade / URD 2.2" SuperGrip Pulley / Airaid M.I.T. / DeckPlate Mod.w/ TRD air filter / 1" PP lift springs w/ Bilstein shocks / Brembo Slotted/Dimpled rotors w/ TRD brake pads / Carbon Fiber dash trim / 60XT PIAA Ion fog lamps on manik grille guard w/ PIAA super extreme H4 headlight & H3 foglight bulbs. / Optima 34R Red Top... Last edited by NoliWan on 12-31-2004 at 07:26 AM Report this post to a moderator | IP: Logged 12-31-2004 06:47 AM Serge Junior Member Registered: Jan 2006 Location: Kyiv, Ukraine Posts: 14 Mr. NoliWan, This was amazing Thanks to instructions provided by you I managed to reprogram my new remote in just 10 minutes. Thanks again. Report this post to a moderator | IP: Logged 01-25-2006 09:16 PM trd_style JDM Style User Registered: Sep 2005 Location: Oklahoma City, Oklahoma Posts: 470 HMM!! This thread should be a sticky!! __________________ 1997 Toyota 4Runner 3.4L V6 Report this post to a moderator | IP: Logged 01-25-2006 09:34 PM voltageGSR Member Registered: Dec 2004 Location: Detroit, MI Posts: 43 very helpful I got through all the steps multiple times but when I get to 6B - it cycles twice; i close the door, and the remote doesn't work. i thought maybe battery..on teh remote, etc.. seems to be ok. Wondering where I'm going wrong? I have a 2001 t4r; remote FCC ID is: 1512Y looks identical to the one I lost..but is this not the right remote? thanks guys! __________________ 2001 Toyota 4runner SR5 4x4 Report this post to a moderator | IP: Logged 06-13-2006 12:52 AM uwgrad97 Member Registered: Apr 2006 Location: Seattle, Washington Posts: 60 That's the same remote I have for my '02 Sport. If you're doing the steps correctly, maybe there's something defective with that remote. Report this post to a moderator | IP: Logged 06-13-2006 02:16 AM voltageGSR Member Registered: Dec 2004 Location: Detroit, MI Posts: 43 i bought it from an ebay member who says it works. plus it seems to respond to the remote; but it cycles twice indicating that it didn't take... any hints? I did the steps several times; I think I am doing it correctly.. __________________ 2001 Toyota 4runner SR5 4x4 Report this post to a moderator | IP: Logged 06-13-2006 11:13 PM voltageGSR Member Registered: Dec 2004 Location: Detroit, MI Posts: 43 any suggestions? seems like the right remote - just unable to pogram correctly? could it need a new battery? seems to respond to the system - ..so didn't think that could be the issue. __________________ 2001 Toyota 4runner SR5 4x4 Report this post to a moderator | IP: Logged 06-16-2006 01:05 AM fooldall Junior Member Registered: Jan 2006 Location: Posts: 21 Does this work for a 1997 as well? I just ordered one for my VIP system on my 97 Limited... Report this post to a moderator | IP: Logged 11-03-2006 02:04 PM pat161 Senior Member Registered: Dec 2004 Location: Central MA Posts: 540 I think the remote you need depends on whether or not you have the alarm. The 1512Y did not work on my 02 Sport w/o an alarm. I needed FCC ID# HYQ12BAN. Hope this helps. Report this post to a moderator | IP: Logged 11-07-2006 11:48 AM BoulderZJ Junior Member Registered: Jan 2004 Location: Boulder, CO Posts: 12 This is amazing. I thought my remote was dead, turns out it had just lost it's programming from the dead battery. I followed this and had it fixed in 15 seconds. Yet another reason I'm glad I got rid of my Jeep. Thanks for the help NoliWan. __________________ 2000 4Runner Limited Alpine 7998, XM, MB Quart reference series all around, Rockford amps and subs Report this post to a moderator | IP: Logged 11-11-2006 08:48 PM mryuk81 Junior Member Registered: Nov 2006 Location: Posts: 4 a. Cycle the power locks 5 times. Does this mean lock/unlock 5 times? I am really unsure. Here is some history: Actually, I didnt buy a new remote. Mine stopped working. I have an 02 T4R. Last week I noticed the *chirp* sound wasnt working any more. Over the weekend... the Keyless Remote stopped working totally. So I radio shacked a new battery in the remote... but it still does not work. I tried these reprogramming instructions, but they do not work either. "Within 3 seconds, the power door locks should cycle (automatically)" This doesnt happen. So I am wondering if I am doing the cycle correctly ... Any Advice would be appreciated. Last edited by mryuk81 on 11-20-2006 at 06:20 PM Report this post to a moderator | IP: Logged 11-20-2006 05:43 PM mryuk81 Junior Member Registered: Nov 2006 Location: Posts: 4 Anyone have ANY ideas ? I have tried this possibly 30 times and it has never worked. Could it possibly be something else wrong ? like a fuse or something? ANY Ideas ? Last edited by mryuk81 on 11-21-2006 at 07:29 PM Report this post to a moderator | IP: Logged 11-21-2006 07:07 PM swtrader Junior Member Registered: Dec 2006 Location: Posts: 3 Programming w/ an alarm I have an alarm on my car that the dealer add. It turns on when the driver door is locked. I can't do the steps with out setting off the car alarm, specifically the close and open the drivers door step. Has anyone seen this problem and have a work around? Report this post to a moderator | IP: Logged 12-14-2006 04:52 AM techno WTF Mate? Registered: Oct 2006 Location: Pittsburgh Posts: 828 quote: -------------------------------------------------------------------------------- a. Cycle the power locks 5 times. -------------------------------------------------------------------------------- Yes, this does mean lock then immediately unlock five times. So it will be locked 5 times and unlocked five times. If you were doing this and the vehicle wasnt doing the automatic cycle thing, then there must be a problem with the computer and not the remote. quote: -------------------------------------------------------------------------------- I can't do the steps with out setting off the car alarm, specifically the close and open the drivers door step. Has anyone seen this problem and have a work around? -------------------------------------------------------------------------------- After you do the lock/unlock cycle thing, the doors should all be unlocked, so your alarm shouldnt be going off. Does your alarm always activate when the unlocked doors are closed? __________________ '00 SR5 4x4 ARB Tundra/OME 32" Muddies n'stuff Report this post to a moderator | IP: Logged 12-15-2006 05:05 PM Advertisement Sponsored Links Ads by Google Supporting this site Also, check out these sponsored links: More Links: All times are GMT. The time now is 10:42 AM. Pages (2): [1] 2 » Last Thread Next Thread Show Printable Version | Email this Page | Subscribe to this Thread Forum Jump: Please select one: -------------------- Private Messages User Control Panel Who's Online Search Forums Forums Home -------------------- Toyota 4Runner Forum-- General Discussions-- 4th Gen T4Rs-- June 2009 T4ROTM-- 3rd gen T4Rs-- Classic T4Rs-- 5th gen T4Rs-- Gallery-- Audio & Electronics-- Off-Roading Stuff-- Comparisons & Reviews-- Accessories-- Special Accessory Offers-- Performance Zone - Tires, Wheels, Exhaust, Superchargers, and more!-- Pimp Zone-- Detailing-- Maintenance-- Problems & Warranty-- Classifieds - buy & sell anything related to the Toyota 4Runner (no commercial ads please)-- Polls-- Off Topic-- Dealers - Your Experience-- FJ Cruiser-- Lexus GX470-- All Other Toyota & Lexus Vehicles4Runner Clubs-- American T4R Clubs (click to view)---- Florida---- Georgia---- (The Rest of) The Deep South---- So Cal---- No Cal---- Pacific NW---- Southwest---- Texas & Oklahoma---- Carolinas---- Maryland / Virginia / WV / D.C.---- Northeast---- New England---- Great Lakes---- Ozarks---- Heartland---- Mountain---- Alaska & Hawaii-- Canadian T4R Clubs (click to view)---- Montreal / Quebec---- Toronto / Ottawa / Ontario---- Edmonton / Calgary / Alberta---- Vancouver / British Columbia---- Winnipeg / Manitoba-- European T4R Clubs (click to view)---- UK---- Germany---- Italy---- France---- Russia---- Scandinavia-- Asia & Oceania T4R Clubs (click to view)---- Japan---- Australia---- New Zealand---- Guam-- Africa & Middle East T4R Clubs (click to view)---- Nigeria---- South Africa---- Egypt-- Latin America T4R Clubs (click to view)---- Argentina---- Brazil---- Mexico-- T4R Meet Announcements & Info-- T4R Meet Pictorials & WriteupsSite relatedAnnouncements - Terms & Conditions of Use - Privacy StatementSoftware Related Questions & AnswersComments & SuggestionsLinks Rate This Thread: Select a rating... 5 .. Best 4 3 .. Average 2 1 .. Worst Forum Rules:You may not post new threads You may not post replies You may not post attachments You may not edit your posts HTML code is ON vB code is ON Smilies are ON [IMG] code is ON < Contact Us - Toyota - 4Runner . org Forum > Powered by: vBulletin Version 2.2.8 Copyright ©2000 - 2002, Jelsoft Enterprises Limited. ***This site is an unofficial Toyota site, and is not officially endorsed, supported, authorized by or affiliated with Toyota. All company, product, or service names references in this web site are used for identification purposes only and may be trademarks of their respective owners. The Toyota? name, marks, designs and logos, as well as Toyota model names, are registered trademarks of Toyota Motor Corporation***
Posted on Jun 13, 2009
where is the fuse box located on a 1993 toyota Camry Lxe? The interior lights, radio,and cigarette lighter are not working.
Hiya,
Your fuses on the '93 Camry are usually located behind the coinbox panel on the dashboard, somewhere near your knee.
...and the major fuse links are in the engine bay, under a secured cover next to the battery:
Hope this helps you...
Cheers,
Posted on Nov 12, 2009
Ignition Cylinder
How do you replace the ignition cylinder in a 93 Toyota Camry?
Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!
CAUTIONSome
models covered by this guidemay be equipped with a Supplemental
Restraint System (SRS), which uses an air bag. Whenever working near
any of the SRS components, such as the impact sensors, the air bag
module, steering column and instrument panel, disable the SRS, as
described in .
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
To install:
Posted on Nov 23, 2008
94 Toyota Camry SDV10 wide body.The headlights all of a sudden went out.If you pull the high beam switch back the headlights will come on but go off when the lever is released.When the headlights switch is turned on the high beam light stays on in the dash even though the headlights are not coming on.The high beam light in the dash stays on no mater if the headlight switch is in the low or high beam position.I have checked all fuses, relays and globes.The fact that the lights come on when the high beam switch is pulled back indicates that the circuit including fuses, globes and relays are all ok.Any help would be appreciated.
it sounds like a bad light switch
Posted on Mar 25, 2010
I back up and drove out of my driveway this morning, drove for 35 minutes to work and try to back in a parking spot. The car made a noise on the back right side and stop my car wont reverse. it will go forward. i am able to put it into gear but, when i accelerate to reverse it won't go. i have a 1993 toyota camry V4.
If the vehcile is V6,then the trans model is the A540E,and if it is the 4 cylinder engine,the trans model is an A140E.Both are 4 speed overdrive transmissions,and sorry to report that on just abot every automatic trans on the road,reverse gear failure is almost always a mechanical problem inside the transmission because there are no shift solenoids involved with reverse as with forward gears.And you did say the forward gears were fine.Good luck.
Posted on Sep 01, 2008
will not start, has no spark. Where to start?? coil,ICM or what and where?
The Toyota 4 cylinder engines have a problem with the electronic units inside the distributor. You will need to replace the entire distributor to fix the problem. You can get aftermarket distributorsat ebay or similar sites for alot cheaper than the originals. It's an easy swap that will take about an hour to do if you are mildly mechanically inclined.
Posted on Aug 18, 2008
I'm just lookiong for a diagram on the fuse/ relay box that by the engine of my car
fuse box is behind ash tray by drivers door
Posted on Jul 03, 2009
1,389 questions posted
Usually answered in minutes!
1,828 Questions
1,753 Questions
1,565 Questions
1,303 Questions
1,134 Questions