20 Most Recent
2006 Toyota 4Runner - Page 6 Questions & Answers
Toyota
could be a lot of different things, .. is it just vibrating or making a certain noise? when did this start happening, what were you doing when you noticed it?
If check engine light is on, i would call around to like jiffy lube and auto zone, see if they have an OBD scan tool to pull codes, they can tell you why your check engine light is on or at least give you the code and you can tell me what the code is or google it and ill tell you what the problem is.
(press add a comment , upper right corner, to reply)
Half the light is out on the information console
Blown bulbs , easy!.
Remove the shroud under the steering column , ( the one where the fuse box and bonnet release is situated)
This will give you access to the bottom screws of the binacle around the speedo ( other screws up from underneath above the speedo)
Once binacle removed you will see the screws holding the speedo in, remove them and ( with the steering tilted fully down) remove the speedo head, there should be 3 or 4 electrical plugs in the back of the speedo ( don't worry they only fit one way and can't be muddled up )
In the back of the speedo are twist clips retaining the bulbs, remove and replace blown bulbs.
Reverse procedure to reinstall speedo.
A magnetic phillips head screwdriver is handy to get the screws back in without loosing them into the back of the dashboard.
I have a 2006 4 Runner 4x4 (63,000 miles). The
The problem is with the ABS sensor which is located near the disk brake rotor, try opening and removing the wheel and cleaning the ABS sensor with a brake parts cleaner (a spray and you can find them anywhere ).
Before doing this I recommend you find a Haynes Repair Manual for this model of car ( Auto Zone or other auto part shops ) this way it'll be easy for you to point out the ABS sensor.
Hope it helps and comment if you need more clarification.
Best
Where can I find the fuse or relay for the Left
If it's just the left one that is giving you trouble, the problem is likely just a bad bulb. They share the same relay. Turn the signal light left, go out and check to see if both bulbs are on. There is a good chance one isn't. Replace it. If that isn't the problem, then you'll have to start checking wires. Get a test light to start with, and see if there is power in the bulb socket. Keep tracing your way back until you find some voltage. It is also possible that both bulbs are burnt out, if neither lights up with the switch on.
VSC Trac and VSC OFF lights come on during warms
Either take it to a dealer to see if the encrypted software can find the fault ,or leave it in the garage in these low temperatures.,lots of vehicles have electrical problems in low temperature enviroments because of the electronics used the components are susceptable to low temperatures
Toyota 4runner sulfur smell
Dear Dgkg4541,
There is a known concern for this situation. The TSB# EG005-06 and
TSB# EG004-06 are Toyota bulletin numbers that explain your condition and lists the parts necessary to correct it.
There are two different bulletins depending on the engine size.The correction is to replace the catalytic converters with units designed to remove the sulfur smell. Even though you have 75K miles on the vehicle,the catalysts maybe covered under an extended emission warranty. If they are,they should be replaced at no charge to you.
Now if they are not covered and you decide to replace them,make sure they use the following updated part numbers. If you have a 2UZ-FE engine,the updated catalyst is #17410-50490 and 17450-50131. If you have a 1GR-FE engine,the updated catalyst is #17410-31600 and 17450-31060. These are the numbers for the units that remove the sulfur smell.
I hope this helps.If you need anything else,drop me a line.Thanks,Chuck
Replace driver side mirror
The entire assembly has to be replaced, can not just replace the mirror.Remove the plastic trim on the inside of the door on the top part of the panel, either comes off with one screw or bolt or simply pull and it has pins in it.Then remove your bolts that hold the mirror in from the inside.If you have a power mirror remove the electrical pigtail, then simply reinstall.Hope I could help..HAPPY HOLIDAYS!!!
How to remove radio from 2006 4runner
dont think you can because their is a circuit board behind it with everything running from and through the ECU .disconnect anything and the factory immobilisor cuts in
06 4 runner
Looks like you have a bad wheel speed sensor. I would pull the rear wheels off, and the brake drums. Look for grease leaking inside the drums, at the center. If so, your rear axle seals are bad...common issue.
Not finding what you are looking for?