2002 Toyota Tacoma - Answered Questions & Fixed issues

Question edited for clarity. Question moved to model category.

Assistance installing a retainer for bumper filler

Tacoma World https://www.tacomaworld.com > threads > assistance-i... Dec 30, 2020 - A couple of weeks ago, I removed most of the front end to do three things. Repaint the lower valance (faded) :thumbsup: tackle some rust ... Front Bumper Filler Install Problems - Tacoma World Nov 22, 2011 Headlight Filler/Bumper Filler Clips? Are these it? Dec 7, 2017 2012 TACOMA FRONT END CONVERSION RG11 ' Page 10 Sep 1, 2013 Another bumper filler question ' Tacoma World Dec 15, 2015 More results from www.tacomaworld.com

How do I install the retainer for a front bumper filler on a

Fixya https://www.fixya.com > ... > Cars & Trucks > Toyota 5 hours ago - Remove the front bumper cover. Remove the tool box and the luggage compartment trim (carpet). Remove the 2 bolts and the nut. ... To install:.

Toyota Tacoma Retainer, front bumper filler, no.3

Toyota Parts Direct https://www.toyotapartsdirect.ca > Toyota__Tacoma RETAINER, FRONT BUMPER FILLER, No.3. This Fits Your Toyota Tacoma. Part Number: 5252335020. Supersession(s): 52523-35020. RETAINER. Fits Tacoma (1995 - 2001) Rating: 4.6 · ‎1,922 reviews · ‎$3.58 ..

Use the supplied key fob unless it is not factory fitted. If fitted by others, I would ask them to advise in the first instance.

TOYOTA TACOMA SERVICE REPAIR MANUAL 2001 2002 2003 2004 DOWNLOAD I hope your problem will be solved:))

Check all vacuum hoses.

Chances are your cv joint is busted and needs replacing that is if your toyota is front wheel driven

Your blend door is actuated by the motor shown below. It is possible the door is sticking or the actuator has internal damage. You would have to remove the heater to access the actuator...

sounds like a bad wire either in the sensor cable or on a connector wifes van did some funky things and it was a bad sensor, also check to be sure there is no corasion on at the connector,

problem areas include park/neutral safety switch, the circuit for the switch or the ECM. code appears when either the ECM detects

2 or more switches are ON simultaneously for R, N, 2 and L positions. Or When driving under conditions (a) and (b) for 30 seconds or

more, the park/neutral position switch is ON (N position).

(2 trip detection logic)

(a) Vehicle speed: 70 km/h (44 mph) or more (b) Engine speed: 1,500 ? 2,500 rpm

the same kind that your taking out

it gotta be the fuses.....

where linkage is

It should be attached to the transmission. Some looks like this one.

.787

Check for water in the fuel as the alcohol in the ethanol gas attracts moisture and after setting it may have drawn too much water into the system .

Well, code 420 means the computer does not think the cat is working to spec. The computer compares data from each O2 sensor - the rear sensor should be staying on the lean side or switching very slowly, while the front sensor switches back and forth between rich and lean several times per minute. If the cat is not working both sensors would read close to the same. So if you replaced both sensors, and you still get code 420, the cat may be blown out. A mechanic would use a scanner to watch the data stream from each sensor, and measure the surface temp of the cat.

Usually an O2 sensor code is a result of another problem. Your problem is coming from the motor & the sensors are just reading it. Bad wires,coils, plus, vacuum leaks even low coolant or running hot will give you O2 sensor codes. Sounds likes you should start on wires themselves. Is it running rough? Missing? Check the plug wires & coils first. Disconnect the batt to clear the codes & take it from there. Good Luck

This code indicates the downstream o2 sensor has failed. Make sure there are no exhaust leaks near the sensor causing false readings. If the connector/wiring is ok replace the sensor

if it says o2 sensor then it must be the bumper

Hi do check the heater control valve and blower control module possible malfunction or faulty, Valve normally situated in engine bay . module will be found on internal heater box .