I'm guessing you can't find it because it's in a separate housing or located under the lower battery tray in the housing (depending on model of engine). Even though this is specific for 1998; I believe it's the same for 1996-1999 Taurus's. I have access to illustrations, but only .gif and/or .bmp extensions were available which would not copy here. If you need these, I will try an extension change to .jpg. Good luck, this should be enough info. It is helpful to include the engine size in question, for future reference...
Thermostat, Water
CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs the service change interval on Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.
1.
WARNING: NEVER REMOVE THE PRESSURE RELIEF CAP UNDER ANY CONDITIONS WHILE THE ENGINE IS OPERATING. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO THE COOLING SYSTEM OR ENGINE AND/OR PERSONAL INJURY. TO AVOID HAVING SCALDING HOT COOLANT OR STEAM BLOW OUT OF THE COOLING SYSTEM OR DEGAS BOTTLE, USE EXTREME CARE WHEN REMOVING THE PRESSURE RELIEF CAP FROM A HOT COOLING SYSTEM OR DEGAS BOTTLE. WAIT UNTIL THE ENGINE HAS COOLED, THEN WRAP A THICK CLOTH AROUND THE PRESSURE RELIEF CAP AND TURN IT SLOWLY UNTIL PRESSURE BEGINS TO RELEASE. STEP BACK WHILE THE PRESSURE IS RELEASED FROM THE COOLING SYSTEM. WHEN CERTAIN ALL PRESSURE HAS BEEN RELEASED, PRESS DOWN ON THE PRESSURE CAP (STILL WITH A CLOTH), TURN AND REMOVE PRESSURE RELIEF CAP
THE ABOVE APPLIES TO ALL MODELS
3.0L (2V) Engine
Removal
Drain the engine cooling system so that the engine coolant level is below the water thermostat (8575) as described.
2.Disconnect the upper radiator hose (8260) from the water hose connection (8592) .
3.Remove the three water inlet connection retaining bolts. Remove the water hose connection .
4.Remove the gasket and water thermostat from the water hose connection . Do not reuse gasket.
Installation
1.Install the water thermostat , gasket and water hose connection as illustrated.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 10-14 Nm (89-124 lb-in).
3.Connect the upper radiator hose to the water hose connection .
4.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water, as described under Cooling System, Draining, Filling and Bleeding procedure.
5.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
6.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
3.0L (4V) Engine
Removal
Drain the engine cooling system so that the engine coolant level is below the water thermostat ; refer to Cooling System Draining, Filling and Bleeding in this section.
2.Raise vehicle on hoist.
3.Disconnect the lower radiator hose (8286) from the water inlet connection.
4.Remove the two water inlet connection retaining bolts. Remove the water inlet connection.
5.Remove the O-ring seal and water thermostat from the water thermostat housing. Inspect O-ring for damage and replace if necessary.
6.If required, remove water thermostat housing retaining bolts, water thermostat housing and O-ring from lower radiator hose tube. Inspect O-ring for damage and replace if necessary.
Installation
1.Install the water thermostat , O-ring, water thermostat housing (if removed) as shown.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 8-12 Nm (71-106 lb-in).
3.Connect the lower radiator hose to the water inlet connection.
4.Lower vehicle.
5.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water; refer to Cooling System, Draining, Filling and Bleeding in this section.
6.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
7.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
3.4L SHO
Removal
Drain the engine cooling system so that the engine coolant level is below the water thermostat ; refer to Cooling System, Draining, Filling and Bleeding in this section.
2.Remove battery.
3.Remove power distribution box.
4.Remove battery tray.
5.Disconnect upper radiator hose and position out of the way.
6.Disconnect the lower radiator hose from the water inlet connection (8K528) .
7.Remove the two retaining bolts. Remove the water inlet connection .
8.Remove the O-ring seal and water thermostat from the water pump (8501) . Inspect O-ring for damage and replace if necessary.
Thermostat
Installation
1.Install the water thermostat , O-rings and water inlet connection as illustrated.
2.Install and alternately tighten the retaining bolts. Tighten bolts to 8-12 Nm (71-106 lb-in).
3.Connect the lower radiator hose to the water inlet connection .
4.Install upper radiator hose . Position spring clamp securely.
5.Install battery tray.
6.Install power distribution box.
7.Install battery.
8.Fill the engine cooling system with a 50/50 mixture of Premium Engine Coolant E2FZ-19549-AA (green), (in Oregon, F5FZ-19549-CC, in Canada, Motorcraft CXC-10), or Ford Extended Life Engine Coolant F6AZ-19544-AA (orange), or DEX-COOL coolant, or a coolant meeting Ford specification WSS-M97B44-D and water; refer to Cooling System, Draining, Filling and Bleeding in this section.
9.Start the engine and check all hoses and connections for leaks. Allow the engine to warm up so that the water thermostat opens.
10.Stop the engine. Top off degas bottle as required to maintain minimum cold fill level.
×