Tip & How-To about Dodge Intrepid

How to remove a front right door panel concorde sedan four door 96

How to remove a door panel, first u must open the door and unscrew the screw that is in the door handle then with a flat head screw driver unhook the plastic conectors to the cover of the handel becarfull not to pull to hard gently pull it as needed then pull the door handle as if opening and then pull the cover of handle out wards and then un detach the electric conector for the door locks then on the bottom handel unscrew the screw that is in the handle then pull out the case that holds it. then unscrew the screws that are on the inside towards the interior of the car there are two then two on the bottom then on the side that opens there should be on or two then pull the panel upwards and then towards your self you should be able to also detach the electric conector for the windows then when your done fixing it the instalation is reverse make sure that you conect the window and door lock conectores and make sure that the door falls in place with window latch. good luck buudy.

Related Questions:

0helpful

1answer

i am trying to take the passenger door panel off of my 2003 kia spectra however it still seems connected towards the front side of the door but i tryed to removed the two tan screws just free spin i do not believe they are attached i didnt want to just pull it and break it

hello,
Disconnect the negative battery cable to prevent shock when handling the door components. Loosen the cable's nut with the pliers and slide it away. Pop off the side-view mirror interior panel with the tweeter on it. Use the door panel trim tool or a flat-bladed tool, such as a putty knife, wrapped in masking tape. Once the panel is off, unplug the speaker connection from behind it. Push the connector's tab in with a flat head screwdriver and pull the connector away. Open the door fully to expose the screw cover on the front part of the door panel. Pry out the screw cover with a flat head screwdriver. Pry out the small centerpiece; not the ring surrounding it. Behind the cover, you'll find a Phillips screw; remove it.
Open the screw cover flap behind the inside door handle. Insert the tip of a flat head screwdriver into the upper-slot; push down to open the flap. Remove the Phillips screw from behind the flap. Pull off the plastic door handle surround piece. Insert the door trim tool behind the panel; pull it back to pull the panel off. Slide the surround piece away from the door panel.
Remove the circular screw cover from the inside door pull storage compartment. Pry it up with the flat head screwdriver. Remove the Phillips screw behind the cover. Remove the screw cover from the rear-edge of the door panel. This cover is similar to the one on the front part of the door panel; pry out the center part, not the ring surrounding it. Remove the Phillips screw behind it.
Remove the two Phillips screws visible along the bottom part of the door panel.
Pry around the perimeter of the door panel with the door trim tool. Pull the tool handle back to pop the door panel clips out. Do this for each side, except for the top. Once the clips are unhooked, the panel is ready for removal.
Gently pull the door panel away from the Optima's door, but only enough to access the area behind it. The connections for the power equipment must be unplugged. Reach around and depress the connection tabs with the tip of the flat head screwdriver; unplug the connection. There are three connections to unplug. Once they are unplugged, pull the door panel away.

Thanks

Read full answer

May 21, 2011 • 2003 Kia Spectra

0helpful

1answer

how to, removing front right door panel on 1996 concorde chrysler 4dr sedan

Read full answer

Aug 16, 2010 • 1996 Chrysler Concorde

0helpful

1answer

Removing a BMW door panel

easy, if it takes you longer than 7 minutes somethings wrong, and most of that time should be looking for tools.
hidden screw behind handle. 3 wires to unhook, courtesy light down below, master control switch plug, and speaker. step 1 unscrew hidden screw, 2) pop all the plastic keepers. 3) twist the handle through the opening without breaking the connection, 4 unhook 3 wires. bingo it's off.

Read full answer

Jul 03, 2010 • 1988 BMW 5 Series

0helpful

1answer

I need to remove the drivers internal door panel

Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Read full answer

Feb 04, 2009 • 2001 Suzuki Swift

0helpful

2answers

removing inter door panel

Unscrew the armrests first.

Then you will see a few (i don't recall but i think there's 2) 5/16 sized screws under that.

The rest of the door panel is held on with plastic clips, which will most likely break, so be prepared to buy a few of them. You can gently "tug" on the door panel, starting at a corner and use a small flat head screwdriver, or a putty knife to pop out the clips.

Read full answer

Jun 01, 2008 • 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?

1,446 views

Ask a Question

Usually answered in minutes!

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

How to remove a front right door panel concorde sedan four door 96

Related Topics:

Related Questions:

i am trying to take the passenger door panel off of my 2003 kia spectra however it still seems connected towards the front side of the door but i tryed to removed the two tan screws just free spin i do not believe they are attached i didnt want to just pull it and break it