How do i take the pins out of the rear brake caliper on a 2000 mitsubishi montero sport so that i can replace the pads. The Pins go through the pads

For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!
Check brake fluid level and top up if neccessary!!!

For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Brake Pads Removal & Installation Front

To Remove:

1. Drain brake fluid to ½ full level in reservoir.
2. Remove the front wheels.
   
   
3. Remove the front brake caliper assembly.
4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
5. Remove the wear indicator from each of the 2 brake pads.

To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.

1. Using a large C clamp or equivalent press piston into the caliper.
2. Apply disc brake grease to the inside of each anti-squeal shim.
3. Install the anti-squeal shims on each pad.
4. Install the pad wear indicator clip to the pads.
5. Install the pads with the pad wear indicator plate facing upward.
6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
7. Install the front wheels.
8. Fill the master cylinder with new clean brake fluid.
9. Pump the brake pedal several times to seat the brake pads.

Rear TMC made rear brake components

TMMK made rear brake components

To Remove:

1. Drain the brake fluid to ½ full level in reservoir.
2. Remove the rear wheels.
3. Remove the caliper slide pins.
4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
5. Remove the rear brake calipers.
6. Remove the 2 brake pads with the anti-squeal shims.
7. Remove the anti-squeal shims and pad wear indicators from brake pads.

To Install:

1. Using a large C clamp or equivalent press the piston into the caliper.
2. Coat both sides of the outer anti-squeal shim with pad grease.
3. Install anti-squeal shims to each pad.
4. Install wear indicators on the 2 brake pads.
5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
7. Fill the master cylinder with new clean brake fluid.
8. Pump the brake pedal several times to seat the brake pads.
9. Install the rear wheels.

Brake Rotor Removal & Installation Front To Remove:

1. Remove the front wheels.
2. Remove the front brake caliper assembly.
3. Remove the front brake pads.
4. Remove the 2 bolts and caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the front wheel disc.

To Install:

1. Align the match marks and install the front disc.
2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the front wheel.

Rear To Remove:

1. Remove the rear wheels.
2. Remove the brake caliper assembly.
3. Remove the brake pads.
4. Remove the 2 bolts and the caliper mounting bracket.
5. Place match marks on the disc and axle hub.
6. Remove the rear disc.

To Install:

1. Align the match marks and install the rear disc.
2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
   • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
   • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
   • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
   • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
5. Fill the reservoir with brake fluid.
6. Bleed the brake system.
7. Install the rear wheel

I believe that the rear discs are warped or the tires are out of round when braking. More likely, the discs. --- The following are the instructions for replacing the front and rear pads for the front/back rotors. 1999-01 Grand Cherokee Front

1. Drain 2?3 of the brake fluid from the front reservoir. Use the bleeder screw at the front outlet port to drain the fluid. If equipped with anti-lock brakes, relieve the system pressure.
2. Raise and safely support the vehicle.
3. Remove the wheels.
4. Insert a small prybar through the caliper opening and pry the caliper (using the outboard brake pad) to bottom the pistons in the caliper bore. NOTE: This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly.
   
5. Pry the caliper support spring out of the caliper.
6. Remove both caliper slide pin bushing caps and slide pins.
7. Lift the caliper from the anchor.
8. Using a piece of mechanics wire, support the caliper so there is not tension on the brake hose.
9. Remove the brake pads from the caliper. Fig. 2: Installing the inward brake pad on the front caliper pistons - 1999-01 Grand Cherokee
   To install:
   
10. Position the brake pads onto the caliper.
11. Position the caliper into place on the anchor.
12. Coat the caliper slide pins with silicone grease and torque them to 21-30 ft. lbs. (29-41 Nm). Install the slide pin bushing caps.
13. Install the caliper support spring in the top of the caliper under the anchor; then, install the other end into the lower caliper hole. NOTE: Hold the spring in the caliper hole with your thumb while prying the spring end out and under the anchor.
    
14. Fill the master cylinder with fluid and bleed the brake system.
15. Before driving the vehicle, pump the brakes several times to seat the pads.
16. Install the wheels.

Rear

1. Drain 2?3 of the brake fluid from the front reservoir. Use the bleeder screw at the front outlet port to drain the fluid. If equipped with anti-lock brakes, relieve the system pressure.
2. Raise and safely support the vehicle.
3. Remove the wheels.
4. Insert a small prybar through the caliper opening and pry the caliper (using the outboard brake pad) to bottom the piston in the caliper bore. NOTE: This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly.
   
5. Pry the caliper support spring out of the caliper.
6. Remove both caliper slide pin bushing caps and slide pins.
7. Lift the caliper from the anchor.
8. Using a piece of mechanics wire, support the caliper so there is not tension on the brake hose.
9. Remove the brake pads from the caliper. Fig. 3: Installing the inward brake pad on the rear caliper piston - 1999-01 Grand Cherokee
   To install:
   
10. Position the brake pads onto the caliper.
11. Position the caliper into place on the anchor.
12. Coat the caliper slide pins with silicone grease and torque them to 21-30 ft. lbs. (29-41 Nm). Install the slide pin bushing caps.
13. Install the caliper support spring in the top of the caliper under the anchor; then, install the other end into the lower caliper hole. NOTE: Hold the spring in the caliper hole with your thumb while prying the spring end out and under the anchor.
    
14. Fill the master cylinder with fluid and bleed the brake system.
15. Before driving the vehicle, pump the brakes several times to seat the pads.
16. Install the wheels.

Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly









4.0L and 4.7L front disc brake assembly




To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
     and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.

1. Remove a small amount of brake fluid from the master cylinder.
   
2. Install a used brake pad into the caliper and compress the caliper pistons.
   
3. Apply disc brake grease to both sides of the inner anti-squeal shims.
   
4. Install or connect the following:
   
   
   
   • Anti-squeal shims to the new brake pads
     NOTE: When replacing worn pads, the anti-squeal shims must be replaced
     together with the pads.
     
     
   • 2 brake pads
     
   • Anti-rattle spring and the 2 caliper pins
     
   • Clip
     
   • Front wheel
   
   
5. Depress the brake pedal several times to seat the brake pads.
   
6. Check the brake fluid level and top off as needed.

Rear
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Rear wheel
     
     
     
     
     
     
     
     
     
     
     
   • 2 cylinder slide pins from rear caliper assembly
     
   • Caliper assembly from rear caliper mounting
     
   • 2 brake pads with anti-squeal shims from rear caliper mounting
     
   • 2 anti-squeal shims from each disc brake pads
     
   • Pad wear indicator plate from the inner side disc brake pad
     
   • 4 pad support plates from the rear caliper mounting

To Install:

1. Install or connect the following:
   
   
   
   • 4 pad support plates on the rear caliper mounting
     
   • Pad wear indicator plate on the inside brake pad
     Note: Install the pad wear indicator facing downward.
     
     
   • Anti-squeal shims on each brake pad
     
   • 2 disc brake pads with anti-squeal shims to the caliper assembly
   
   
2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
   pins.
   
3. Install or connect the following:
   
   
   
   • Disc brake caliper assembly with 2 caliper slide pins
     
   • Torque to 65 ft-lbs (88 Nm)
     
   • Rear wheel
   
   
4. Depress the brake pedal several times to seat the brake pads.
   
5. Check the brake fluid level and top off as needed.

--- Removal & Installation
Front
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Front brake caliper assembly
   
   
3. Make matchmarks on the disc and the axle hub.
   
4. Remove the front disc.

To Install:

1. Align matchmarks and disc onto axle hub.
   
2. Install or connect the following:
   
   
   
   • Front brake caliper assembly with the 2 bolts
     
     
     
     1. Torque to 90 ft-lbs (123 Nm)
     
     
   • Front wheel

Brake Pads Removal & Installation Front To Remove:

1. Remove the front wheels. Front brake caliper (exploded view)
   
   
2. Loosen the caliper bleeder.
3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
4. Support the caliper.
5. Open the brake bleeder. Press the caliper piston into the bore.
6. Close the bleeder after the piston has reached the bottom of the caliper bore.
7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
8. Remove the slide pins and bushings from the caliper support.

To Install:

1. Lubricate the slide pins and bushings with brake grease.
2. Install the bushing on the slide pin.
3. Install the slide pin on the caliper support.
4. Install the brake pad support plates on the caliper supports.
5. Lubricate the anti squeal shims with brake grease.
6. Install the anti squeal shims on the brake pads.
7. Install the pad wear indicator facing upward and install the pads on the caliper support.
8. Install the caliper on the support.
9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
10. Fill the reservoir and bleed the brakes.
11. Install the front wheels.

Rear To Remove:

1. Remove the rear wheels.
2. Loosen the caliper bleeder. Rear brake caliper (exploded view)
   
   
3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
4. Support the caliper.
5. Open the brake bleeder. Press the caliper piston into the bore.
6. Close the bleeder after the piston has reached the bottom of the caliper bore.
7. Remove the brake pads, support plates, and anti squeal shims.
8. Remove the slide pins from the caliper support.

To Install:

1. Lubricate the slide pins with brake grease.
2. Install the slide pin on the caliper support.
3. Install the brake pad support plates on the caliper supports.
4. Lubricate the anti squeal shims with brake grease.
5. Install the anti squeal shims on the brake pads.
6. Install the rear pads on the caliper support.
7. Install the rear caliper on the support.
8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
9. Fill the reservoir and bleed the brakes.
10. Install the front wheels.

Remove all rust from pad and caliper sliding surfaces,eg metal to metal,not the pins,they get synthetic brake lube. Apply anti-seize to all sliding surfaces. Make sure you can screw in the rear caliper piston,if applicable, and manually ratchet up the parking brake,after caliper and pads are on. Bleed/Flush all 4 Wheels. Make sure you can slide the pads back and forth,before lubing end tabs. You may need to file a little off the ends or just remove the paint. Make sure parking brake cables are really releasing.

You need to make sure the caliper pieces slide freely on the pins and the piston also moves freely. I just did my daughters GM car. I had to pull back the rubber boots, thoroughly clean the pins and relubricate them with the correct lubricant. Worst case scenario, you may have to replace the caliper pins or get rebuilt calipers.

Without contaminating everything, try some penetrating oil sprayed carefully on the pins and let it set overnight and then some light tapping with a small hammer to break any rust bond.