Cant get rear door open. Need to get to the 4 screws below door pocket. How do i do this.

1. Remove the door handle bezel.

2. Insert a flat-bladed tool between the door handle bezel and the trim panel in order to release the handle bezel tab retainers.

3. Remove the door trim panel upper extension.

4. Release the upper extension by pulling outward on the front edge in order to release the upper retainer clips.

5. Remove the upper extension from the trim panel by lifting up and out.

6. Using a suitable flat bladed tool, gently pry the manual lock lever from the door trim panel. Remove the trim panel screw.
*Remove the screw (2) from within the opening where the manual door lock lever resides.
*Remove the screw (3) from the opening in front of the armrest.
*Remove the screw located beneath the map pocket, if equipped.

7. Carefully slide the trim panel up in order to release the retainers from the door. Disconnect the electrical connectors.

Note: the top part of the door panel is not separate from the bottom. The "upper extension" is just the small triangle piece directly behind the mirror on the interior.

Simplified instructions
Remove the bezel around the door handle.
Pry out the manual lock.
Remove the 3 or 4 screws depending on options
Slide the door panel up off of the engagement tabs.

Good luck and thank you for using Fixya.

As per the Haynes manual for your vehicle.
DOOR WINDOW GLASS-REMOVAL AND INSTALLATION:
1. Remove the door outer panal.
2. Lower the window glass.
3. remove the two nuts and one screw securing the glass.
4. Remove the glass by lifting it up carefully and rotating it inward.
5. Installation is reversal of removal.

DOOR OUTER PANAL-REMOVAL AND INSTALLATION:
1. Remove door trim panal.
2. Remove the outside mirror. Remove the foam block from the mirror opening.
3. Remove the outside door handle.
4. Open the door and pry thhe outer sealing strip out of the window glass opening.
5. remove the door panal screws.
6. Detach the front and rear of the outer panel, then lift it toward the rear to remove it.
7. Installation is the reverse of the removal procedure. Apply thread locking compound to the panel retaining screws.

OUTSIDE DOOR HANDLE-REMOVAL:
1. Pull handle out and puch the centers of the retaining pins through the pins, then remove them and detach handle. (These pins are located underneath the handle.

Hope this helps, let me know if you need any other help.

4-Cylinder Engines

1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
   
2. Carefully pry off the cap(s) in the armrest pocket, then remove the screw(s).
   
3. Carefully pry off the cap under the armrest and remove the screw.
   
4. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
   
5. Unplug the electrical connectors for the power windows, power mirror and courtesy light.
   
6. Carefully lift the door panel up and away from the door frame.
   
7. Installation is the reverse of the removal procedure.
   

V6 Engine

1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
   
2. Carefully unsnap the rear of the speaker grill, lift and pull back to release it and remove the grille.
   
3. Remove the panel mounting screws located around the perimeter of the speaker.
   
4. Remove the cap and screw in the pull pocket of the armrest.
   
5. Slide the pocket back slightly to release the front hook, then lift up, detach the electrical connectors and remove the pocket assembly.
   
6. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
   
7. Carefully lift the door panel up and away from the door frame slightly and disconnect the speaker connector.
   
8. Installation is the reverse of the removal procedure.
   

if it is the hatch there ae screws in the pockets inside door panel remove these then it just pops off if it is a 4 door and you want a rear door there are screws in bottom edge of door and you need to remove cover on door handle where there are 2 screws under cover then panel pops off

You need to undo the door trim (difficult at closed door but no other way) and replace the door opener cable

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then just remove the bolts for the mirror

Hi Racegas, I am assuming you need to take off one of the rear door panels. The 1/4 glass sunshade needs to be removed to gain access to a hidden screw.If you are looking at the sunshade from inside of the car. Lower the window, and look at the op of the shade assembly on the inside. You will see a square looking hole. Using a small pocket screw driver, or equivalent, insert the screwdriver into the hole and pry upwards. Pull the assembly to you at the same time. The clip that holds the assembly in place is pretty stout. You may want to shine a flashlight inside the hole to get a better idea of how far to pry the retaining clip up. Just in case you need to know, there are 2 screws under the trim strip that is adjacent to the release handle and one toward the bottem of the door near the interior pocket.

UNSNAP PUSH-PIN FASTENERS FROM BOTTOM OF CENTER CONSOLE
AND REMOVE BOTTOM PANEL.
2. EXTRACT 4 SCREWS FROM BOTTOM EDGE OF BEZEL. EXTRACT 4
SCREWS FORM INSIDE DASH BELOW POCKET. PULL CUP HOLDER/
POCKET ASSEMBLY OUT OF DASH AND REMOVE.
3. OPEN GLOVE BOX AND REMOVE STOPPERS. EXTRACT 2 SCREWS
FROM RIGHT SIDE OF CENTER DASH BEZEL..
4. FROM BELOW STEERING WHEEL EXTRACT 2 SCREWS FROM BOTTOM
EDGE OR PANEL, UNSNAP UPPER EDGE OF PANEL, UNPLUG, AND
REMOVE.
5. UNSNAP TOP EDGE OR CENTER LOWER BEZEL, UNPLUG, AND REMOVE.
6. EXTRACT 2 SCREWS FROM SIDES OF POCKET.
7. UNSNAP RADIO/AC CONTROL DASH BEZEL, UNPLUG, AND REMOVE.
8. EXTRACT 2 SCREWS FROM EACH SIDE OF THE RADIO BRACKET
ASSEMBLY TO REMOVE RADIO FROM DASH/AC BEZEL.

there are 4 torx T-15 screws, one in the rear map pocket, one under the air bag logo plastic clip, one under the wood trim (pry the trim off carefully), and one holding the door handle assembly (also revealed when you remove the wood burl cover). Pick up a pry tool at autozone, about 5 bucks to pry the clips out without breaking