Question about 2001 Chevrolet S-10

1 Answer

What is the easiest way to replace the oil pan cover gasket on a 2001 chevy s-10 4cyl. 5 speed

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,623 Answers

There is no easy way. The engine has to be hoisted or jacked high enough to allow clearance to remove the oil pan.

Posted on Aug 28, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will i have to remove motor to replace oil pan gasket on a 2001 gmc sonoma 2.2l 5 speed


You may have to loosen the transmission also to get enough room to remove it without taking the motor out. Make sure your pan is not cracked first. Also be careful when lifting the motor as to not damage anything on top of the engine.

Nov 29, 2015 | GMC Cars & Trucks

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

Replacing oil pan gasket 1998 chevy silverado 305 cu.in.


REMOVAL PROCEDURE
  1. Remove the oil level indicator tube.
  2. Raise the vehicle.
  3. Remove the engine oil and the engine oil filter.
  4. Remove the oil filter adapter.
  5. Remove the starter.
  6. Remove the flywheel inspection cover.
  7. Remove the engine mount through bolts.
  8. Raise and support the engine.




  1. Remove the oil pan nuts and bolts. Note the location of any studs to assist reassembly.
  2. Remove the engine oil pan and the gasket.
  3. Clean all sealing surfaces. Refer to Oil Pan Clean and Inspect under Engine Unit Repair.
INSTALLATION PROCEDURE


  1. Install the engine oil pan and a NEW gasket. Refer to Oil Pan Installation under Engine Unit Repair.
  2. Lower the engine onto the mounts.
  3. Install the engine mount through-bolts.
  4. Install the starter.
  5. Install the flywheel inspection cover.
  6. Install the engine oil filter and the engine oil.
  7. Install the oil filter adapter.
  8. Install the oil level indicator tube.

May 04, 2015 | 1998 Chevrolet Chevrolet silverado

2 Answers

How do you replace an oil pan for 2001 mitsubishi eclipse?


Assuming you're talking about the lower oil pan...it's very simple

1. Lift at least the passenger front side of the car using a jack, jack-stand, and blocks on the rear wheels

2. Drain the oil out of the pan by removing the drain plug (just like an oil change)

3. Remove all of the bolts on the outside edge of the oil pan (should be about 11)

4. After all of the bolts have been removed the oil pan is free to come off. It might still be stuck on and a few gentle taps with a rubber mallet with knock it loose. Be aware that there is still some oil inside the pan, so this step will be pretty messy

5. Clean the surface of the engine where the oil pan was mounted against

6. Take your new oil pan and place the gasket around the rim of the pan (if not using a gasket then put liquid gasket around the rim. This is important to ensure the pan doesn't leak)

7. Place the oil pan on the engine and bolt it back on. Start by tightening on bolt, then one as close to 180 degrees across from it. Repeat until all the bolts are tightened.

8. Fill the oil pan with new oil. You may also wish to remove and replace the oil filter.

9. If you used liquid gasket, give it a few hours to set (look at contained for a recommend amount of time to wait). If you used a rubber gasket, you don't need to wait.

10. Start the engine and check for leaks. If you notice any oil leaking from around the seal then turn the engine off, go back to step 2 and then repeat from there on. If you don't see any leaks, you are good to go.

Dec 29, 2010 | 2001 Mitsubishi Eclipse

2 Answers

How do you replace a gasket and cover for timing chain and rear seal gasket for oil pan on a 1978 Chevy 350 motor


the oil pan will need to be removed to repalce the rear seal, so replace the front seal and gasket then, replace the timing chain/gears if sloppy, then reinstall the oil pan.

Dec 11, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

How to fix a front leaky oil seal in a 1995 Toyota Camry LE


Three seals to check. easiest is the valve cover seal. Number and remove the 4 wires going into your spark plugs. remove 4 nuts holding the cover and replace seal.
Next easiest is the distributor O-ring. Remove air filter assembly remove the distributor cap, then the distributor. With the valve cover still off, loosen the 2 bolts that clamp the distributor down. Remove the 2 terminal leads going into the distributor (4 wire terminal/2 wire terminal) Mark the case of the distributor and the case of the head with one line so you can line it back up on reinstallation. remove the 3 bolts holding the distributor down. Replace O-ring. replace distributor, align, tighten the 2 bolts, then tighten the 3 bolts. replace terminal wiring and cap. replace air filter assembly. Replace valve cover with new gasket. Place spark plug wires back into their proper places. The last one is the oil pan gasket. Drain all oil and remove all blots holding the pan. drop the pan and replace the gasket. Put it all back into place. Do not over tighten the pan bolts as this will cause the gasket to deform, making it leak again.

Nov 22, 2010 | 1995 Toyota Camry

1 Answer

I was told there are two oil pans on Mazda Tribute 2001 (upper & lower) 4 cylinder manual. I have an oil leak do I replace both?


There are two gaskets, one is between the lower pan and the upper pan, and the second is between the upper pan and the engine. You only need to replace the gasket that leaks. If both are leaking, replace them both. To find out where the leaks are, raise the car, get underneath, and look closely all around the oil pans to see where the oil is coming from. Use a flashlight if necessary. You should be able to trace any leaking oil upward to its source.

The oil pan gaskets are not necessarily the only sources of oil leaks. Check to see if any oil is coming from behind the timing cover, and look for oil coming from the valve cover gasket.

Mar 21, 2010 | Mazda Tribute Cars & Trucks

2 Answers

How much to change a oil pan gasket for 2001 grand prix 3.8 gt


If you want to repair the oil pan I would also check lower engine mount for leaking oil and cracks in anti sway bar near fitting's. This due to engine mount is oil filled. OEM sway bar is made of tubular steel and they crack easy. Replacement sway bar is solid steel. Here's the kicker. When they pull the lower frame to service oil pan. The engine mount and sway bar are attached to that frame. A honest mechanic should only charge for parts ($35 for mount and $100 for sway bar) and maybe a extra hour. My mechanic did all in 5 hours. FYI gasket is only $35 bucks. Good luck

Feb 26, 2010 | 2001 Pontiac Grand Prix

1 Answer

HOW TO PUT A OIL PAN GASKET ON A 2001 CHEVY MALIBU?


pull the vehicle on ramps or put on jack stands. set the emergency brake pull off flywheel cover if there is one remove all the bolts from pan and drop it down might catch on oil pump. pull off old gasket and replace with new one

Sep 01, 2009 | 2001 Chevrolet Malibu

Not finding what you are looking for?
2001 Chevrolet S-10 Logo

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...