Question about 2001 Chevrolet Silverado 1500

1 Answer



Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Will 2001 4l60e transmission guts fit in 1998 z71 4x4 with 4l60e

Posted on Jan 12, 2019


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 2 Answers

SOURCE: 1997 XK8 Transmission Failure. Will 2001 XK8 transmission work

I had a similar problem with my 1997 XK8. Apparently the transmission will not last much more than 100,000 miles. You need to replace the clutch in the transmission - cost between $2,500 and $4,000.

Posted on Jul 27, 2009


  • 50 Answers

SOURCE: will any 4l60e transmission from 1993 to 2004 work

No they will not interchange. The input shaft pump and converter are different. Internal parts will interchange. You will need 96-early 99 model That is old body style.

Posted on Mar 27, 2010


  • 11 Answers

SOURCE: transmission interchange

Yes, but the steps involved in switching the 4wd output shaft, over to the 2wd output shaft are very involved. Thats assuming that the bellhousings are identical. (detachable bellhousing) That you do not need a 30 spline input shaft for your torque converter (96+ blazer input shaft splines are all 28 splines, however you may need a 30 spline in order for the correct torque converter to fit your 2wd vehicle.) You will need to know what 2wd output shaft you need, there are quite a few variations. Then you would need to take the pan off, pull the shift soleniod blocking access to the lockup soleniod, remove the lockup soleniod, remove the pump bolts, pull the pump, unhook the 2nd/4th, band remove the reverse drum - 3/4 drum (by pulling the input shaft twards you) then remove the yellow snap ring holding the output shaft in place. Now the output shaft is able to be removed and switched. Re instalation of the drums/pump is tricky as well, as all the clutches need lined back up to slide back onto there corasponding splines. Long story short, it would be alot more trouble than its worth. : )

Posted on Apr 10, 2009


  • 2 Answers

SOURCE: what model 4L60E tranny's can I put in my 1998

the way i figured which 4l60e works with my truck was to get the service number off of the ecm. Then I took that ecm service number and searched for it on ebay. People selling that same ecm will usually list what other vehicles that ecm works on. Then I went to the u-pull&pay and got a tranny out of one of those vehicles. I do know that after 95 there is an extra pin in the main wiring harness that goes to the PWM. My 94 tranny didn't have that pin. Also try pulling the main wiring harness out of your tranny and with a mirror look down into the tranny and get the pin configuration. Make sure the one you get also has that same pin layout.

Posted on Mar 04, 2010



  • 389 Answers

SOURCE: interchange body parts with 2001 Silverado 2500

1999 through 2002 Chevrolet Silverado or 1999 through 2002 GMC Sierra.

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Will 2008 Silverado with 4.3 engine transmission interchange with 2009 silverado

Hi jim with your serial number you would no call part department they will tell what the number of you trasm its all got to do with what kind of gear ratio your computer was program to fit the trasmission

Mar 13, 2015 | Chevrolet Silverado Cars & Trucks

1 Answer

Years interchange

!995-2000 are the small frame in 2001 the steering has gone to rack and pinion the early frames are still gear box steering 1994 and earlier (1989) are torsion suspension but narrow frame rails and 2wd and 4wd are different

Aug 12, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Will a 99 Tahoe transfercase work in a 2000 silverado 2500 they both have the np246 transfercase with push button 4X4

If the drive line & wheel shafts fit I don't see an issue except gear ratios. I've never heard of anyone trying but if u know how to read a micrometer and tape measure you'll figure it out. If you do not, I wouldn't attempt it. Good luck.

Feb 06, 2012 | 2001 Chevrolet Silverado 2500HD

1 Answer

Change the belt alternator of my chevy silverado 2001 /2500

There is a slot in the front of the belt tensioner a 3/8ths socket extention will fit into this slot put the extention on a socket wrench and push the tensioner toward the engine this will release the spring tenition from the belt and it will come off

Dec 17, 2010 | 2001 Chevrolet Silverado 2500

1 Answer

Interchange body parts with 2001 Silverado 2500

1999 through 2002 Chevrolet Silverado or 1999 through 2002 GMC Sierra.

Mar 19, 2010 | 2001 Chevrolet Silverado 2500HD

1 Answer

Will a 2006 silverdo rear differential with drum brakes and 4:10 gear fit a 2004 silverado rear diffferential with disc brakes and 3:73 gears

Your local junk yard will have an interchange guide. I can tell you your speedometer will be off and you will probably get worse gas mileage. Can you swap the break set around. I would almost bet if you have ABS it will be an issue.

Mar 05, 2010 | 2004 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,623 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides