2002 PASS-LOCK RELEARN

This an example of relearn procedure.
Clear all codes.
start the engine or try to.
The system long tamper mode and security lamp will flash for ten minutes
Leave the ignition switch in the run position until the lamp stops flashing.
Turn ignition switch to off, turn ignition switch back to the run position.
The theft system lamp will flash again as the system learns. When the lamp stops flashing, the learn cycle is complete. Some info says to use battery charger on low setting because this procedure can take a while. The passlock key is just a mechanical key, no pellet, no transponder. It's the tumbler that communicates with pass lock sensor not the key. If the relearn doesn't work, I'm not sure what to tell you?

Take it to the dealer or a ASE certified repair shop .or go on youtube an check out videos on anti-theft by pass for GM vehicles .There are a few different type's . VATS , pass key 1,2 or three . Being yours is a 2002 model year it isn't the VATS .
Passlock™ System
The theft deterrent system has been incorporated into the body control module (BCM). The theft deterrent is provided in order to prevent the vehicle operation if the correct key is not used in order to start the vehicle. The ignition key turns the lock cylinder. The cylinder rotation produces an analog voltage code in the Passlock™ sensor. This voltage code is received by the BCM. The BCM compares the voltage code to the previously learned voltage code. If the codes match, a class 2 message is sent from the BCM to the powertrain control module (PCM)/vehicle control module (VCM). The message enables the fuel injectors.
The design of the Passlock™ system is to prevent vehicle theft by disabling the engine unless the ignition lock cylinder rotates properly by engaging the correct ignition key. The system is similar in concept to the PASS-Key® system. However, the Passlock™ system eliminates the need for a key mounted resistor pellet. The components of the Passlock™ system are as follows:
• The ignition lock cylinder
• The ignition switch
• The Passlock™ sensor
• The Body control module (BCM)
• The security telltale
• The vehicle/powertrain control module (VCM/PCM)

You don't need to program key's with this anti-theft system , there is no chip inside . Did you get a correct lock cylinder. . On this system there is a pass lock sensor in side an the lock clinder has a magnet !
Passlock™ Sensor
The passlock™ sensor is inside the upper right side of the steering column. The passlock™ sensor contains 2 hall effect sensors. The tamper hall effect sensor is on the top. The security hall effect sensor is under the tamper hall effect sensor. Both of the hall effect sensors monitor the magnet of the lock cylinder through an opening. The tamper hall effect sensor is physically placed on top of the security hall effect sensor. This arrangement enables the tamper hall effect sensor to engage first if an intruder attempts to bypass the passlock™ sensor by placing a large magnet around that area of the steering column. There is a tamper resistor inside the passlock™ sensor in order to help prevent tamper to the system. Passlock™ equipped vehicles have a selection of 10 different security resistors ranging from 0.5K ohms up to 13.6K ohms. Installing one of the security resistors inside the passlock™ sensor will generate a unique passlock™ code. All 10 combinations of the passlock™ sensor have the same part number. However, you cannot simply replace the passlock™ sensor and expect the system to operate properly. Always start by performing the Diagnostic System Check first and following the instructions.
Body Control Module
The Body Control Module (BCM) contains the theft deterrent system logic. The BCM reads the passlock™ data from the passlock™ sensor. If the passlock™ data is correct, the BCM will pass theft. The BCM will then transmit the code password to the VCM/PCM.
During the tamper mode the vehicle may start. The vehicle will then stall. If the BCM receives the wrong passlock™ data, the VTD will immediately go into the tamper mode. The tamper mode will lock-out the vehicle fuel injectors for 10 minutes. The SECURITY indicator will flash while the VTD is in the tamper mode.
If the passlock™ sensor sends a correct password to the BCM when the ignition is in the ON position, the BCM will send a fuel enable signal to the VCM/PCM. The VCM/PCM will not disable the fuel due to any BCM message for the remainder of the ignition cycle.

You only need to do a relearn if one of these are replaced
Use this procedure after replacing:
• Passlock™ Sensor
• BCM
• VCM
• PCM

Did you replace any of these ?

30 Minute Re-Learn Procedure
Turn ON the ignition, with the engine OFF.
Attempt to start the engine, then release the key to ON (vehicle will not start).
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF.
Turn OFF the ignition, and wait 5 seconds.
Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes ( the vehicle is now ready to relearn the Passlock™ Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK).
Important: The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
Start the engine (the vehicle has now learned the Passlock™ Sensor Data Code and/or password).
With a scan tool, clear any DTCs if desired (history DTCs will self clear after 100 ignition cycles).

no the power control module runs the whole car and the pass lock you maybe can do without it controls the security systems but the pcm is the brain of the car

Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can order one from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

Without a scan tool you may have momentary starter interruptions while history clears itself.

Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can order one from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

Without a scan tool you may have momentary starter interruptions while history clears itself. Keep me posted, be glad to know you got your car running 100% again soon.

You can't turn it off, but you can buy and bypass module.

Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can orderone from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure
1.) Turn ON the ignition, with the engine OFF.
2.) Attempt to start the engine, then release the key to ON; the vehicle will not start.
3.) Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF.
4.) Turn OFF the ignition switch, and wait 5 seconds.
5.) Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes.
The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
6.) Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password.
7.) With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles.

Without a scan tool you may have momentary starter interruptions while history clears itself.

Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can orderone from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Your Passlock may need to relearn the ignition keys, if the ignition lock has gone bad like my in-laws Grand Am Gt, here is what i did so they will not get stranded any more. Buy a Passlock by pass module for around $70.00. You can orderone from GMPASSLOCK.COM in the mean time try resetting the Passlock. Good luck

Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

The passlock system is sensitive to voltages on the circuit. Make sure all your power and grounds are clean and tight. Make sure you car battery at 100%. Check the connector at the pass lock sensor in the steering column is good. Alot of time just by unplugging and plugging the connectors solve the conceern. If all are good, I would wait to see if it happens again. Then I would change the ignition cylinder. I would not recommend it if your not familair with coding cylinders. What you did is relearn the passlock voltage reading the computer sees when you first turn the key.

When the ignition key is used to turn the ignition lock cylinder to crank, start, a magnet on the lock cylinder passes close to the Passlock™ sensor within the ignition lock cylinder case. The magnet activates the security hall effect sensor in the Passlock™ sensor which completes a circuit from the security sensor signal circuit through a resistor to the security sensor low reference circuit. The resistance value will vary from vehicle to vehicle.