Question about 2002 Mitsubishi Montero

Open Question

I need the head bolt torque of the mitsubishi montero 2002 3.5

Posted by Anonymous on

Ad

5 Suggested Answers

Anonymous

  • 362 Answers

SOURCE: torque specs for the main bearings, connecting rods and heads

Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.
69de06e.png

Posted on Jan 24, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: mitsubishi montero radio unlock

i tried to many codes for the radio lock and now it just says off. how to is fix it?

Posted on Feb 08, 2009

Ad
rockitman187

Randy Hough

  • 2559 Answers

SOURCE: asistance to change the thermostat in a 2002 mitsubishi montero limited

Follow the top radiator hose down to the water outlet. The thermostat is inside the water outlet,Just remove the bolts,replace thermostat,replace gasket,bolt back in place.

Posted on May 28, 2009

junmag

Jun Magno

  • 175 Answers

SOURCE: Blown head gasket

i think you are reffering to a 4D56 engine. just type 4D56 workshop manual .pdf download on your browser and you fill find several free downloads. everything you need to overhaul the engine is there

Posted on Jun 02, 2009

tberan1

  • 523 Answers

SOURCE: I need to change my spark plugs on a 04'

If you'll need to remove the intake (or plenum) from the engine there are @ 8-10 No. 12 nuts and or bolts which hold this in place. There are also 1-2 bracket (check by the firewall) you'll need to unbolt too. Be certain to replace the gasket that is found between the plenum and the intake and do not over tighten these nut/bolts only 20ft pounds or so. If you do remove this you'll have to remove the air inlet, throttle cables and remove hoses from the throttle body, some of which carry coolant to properlly preheat the air before enteringthe engine. I have worked on several early 89-93 Monteros without having to remove this for plugs; perhaps different under the hood of the sport.
I hope this may have helped,
Tom

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi montero alternator


Loosen the center bolt on the pulley first.

Jan 26, 2014 | Cars & Trucks

1 Answer

1996 pajero 2800 turbo v40 engine need torque settings on head bolts


go online n look a little harder...these torque settings for ur car should be online somewhere if u look hard enough...ask dealer for a diagram...then can often print off their computer whatever info ur lookin 4...

Nov 27, 2013 | 1991 Mitsubishi Montero

1 Answer

Torque the cylinder head bolts for mitsubishi lancer 2002


Try this
I dont know which engine you have.

420a
1. Torque all center bolts to 25 ft-lbs, torque the 4 corner bolts to 25 ft-lbs
2. Torque all center bolts to 50 ft-lbs, torque the 4 corner bolts to 50 ft-lbs
3. Re-Torque all center bolts to 50 ft-lbs, re-torque the 4 corner bolts to 50 ft-lbs
4. Tighten all bolts in the sequence from #1-#10 an additional 1/4 turn.

7-Bolt 4G63
1. Torque all bolt to 58 ft-lbs in order
2. Loosen all bolts completely to 0 ft-lbs
3. Torque all bolts to 15 ft-lbs in order
4. Tighten all bolt 1/4 turn in order
5. Tighten all bolts an additional 1/4 turn in order.

ARP Head Studs
1. Tighten all bolts to 40 ft-lbs
2. Tighten in steps of 10 ft-lbs increments until the specified torque that you are looking for is reached. This can vary with the amount of boost you plan on running.

Jun 30, 2011 | 2002 Mitsubishi Lancer

1 Answer

V6 T3000 need torque specs has throttle body injector


3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

Aug 15, 2010 | 1994 Mitsubishi Montero

2 Answers

Replacing cylinder head on 1986 montero with 2.6 timing chain. just need timing marks and head torque specs.


ok
42011354
  1. Torque all bolts except No. 11 to 69 ft. lbs. on a cold engine or 75 ft. lbs. on a hot engine.
  2. Torque cylinder head to chain case cover bolts (No. 11) to 156 inch lbs.
  3. 42011356

Sep 17, 2009 | 1986 Mitsubishi Montero

1 Answer

Blown head gasket


i think you are reffering to a 4D56 engine. just type 4D56 workshop manual .pdf download on your browser and you fill find several free downloads. everything you need to overhaul the engine is there

Jun 02, 2009 | 1991 Mitsubishi Montero

1 Answer

Asistance to change the thermostat in a 2002 mitsubishi montero limited


Follow the top radiator hose down to the water outlet. The thermostat is inside the water outlet,Just remove the bolts,replace thermostat,replace gasket,bolt back in place.

May 28, 2009 | 2002 Mitsubishi Montero

1 Answer

Torque specs for the main bearings, connecting rods and heads


Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.
69de06e.png

Jan 24, 2009 | 2000 Mitsubishi Montero

Not finding what you are looking for?
2002 Mitsubishi Montero Logo

Related Topics:

922 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...