Does the oil light come on BEFORE the engine shuts down? I have to ask because it is NORMAL for the oil light to be on when the engine is not running. I had a customer that said the same thing just last week. After we wasted a bunch of time (which the customer ended-up paying for) checking the oil level, the oil pressure, and verifying correct oil pressure gauge, light, and sending unit operation, it turned out that the crankshaft position sensor was bad and causing the engine to shut down and it had absolutely NOTHING to do with the oil light - it was functioning as designed.
If the oil light is coming on before the engine shuts down, the first thing you need to do is check your oil level. If the oil level is OK, you need to check the oil pressure with a gauge to determine if there is an actual engine oil pressure problem or if the oil pressure sending unit, gauge or light is malfunctioning. Also, it is highly advisable to not drive the vehicle AT ALL if the oil pressure light is coming on while driving until the cause of the light coming on has been determined and repairs have been made. Otherwise, SEVERE ENGINE DAMAGE may result.
SOURCE: Took down transmission pan in 2003 lincoln avaitor
Sounds like your filter is loose in your ****** or you forgot the gasket and the pump is not sucking any transmission fluid
SOURCE: 2004 Avaitor brake problem
right behind the rotor itself just inside are babypads and if they are loose it will make the car acts as if the emergency brakes are on so take everything off and behind the rotor you should see these little pads
SOURCE: I don't have a manual for my 2004 lincoln Avaitor
KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code. The factory-set code is located: • on the owner's wallet card in the glove compartment • or at your dealer. When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation. This system will disable the power door lock controls. These will not work until the vehicle is disarmed. Programming your own personal entry code To program your own code: 5. Enter factory set code (keypad will illuminate when pressed). 6. Press 1/2 control within five seconds of step 1. 7. Enter your personal 5 digit code. Enter each digit within five seconds of previous one. 8. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. Locks and Security 149 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code. The keyless entry pad is disabled for 1 minute after 7 unsuccessful attempts (35 consecutive button presses) at entering a valid key code. The keypad will flash during this 1 minute mode. However, the 7/8 and 9/0 controls will still lock the vehicle. Anti-scan will be turned off after: • one minute of keypad inactivity. • the remote entry transmitter UNLOCK button is pressed. • the ignition is turned to the ON position. Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal code (driver door unlocks) and press the 3/4 control within five seconds. Locking the doors with the keyless entry system It is not necessary to enter the factory or personal code prior to locking all doors. To lock the doors: • with the driver's door closed, press the 7/8 control and the 9/0 control at the same time.
SOURCE: Check engine lights stays on with rough idle 2004
You will have to connect a scan tool to the vehicle to pull any codes that the computer is sending.
The number of the code will help us find the problem.
A rough idle could be a fuel or electrical problem.
Please let me know what you find.
Testimonial: "Will determine level of satisfaction after suggested diagnose check"
SOURCE: my 2004 Lincoln Avaitor has a bouncy ride
it may have something to do with your shock absorbers, you might have to take the vehicle to a suspension specialist & have it checked for suspension damage.....hope this helps....cheers.
321 views
Usually answered in minutes!
×