Cars & Trucks Logo
Anonymous Posted on Feb 22, 2012

Chi got a 2000 chevy silverado with a 5.3 when its if u go to take off it will buck or if i hold it to the floor it will back fire .got mass air flow sensor code

Chage plug, wires, fuel filter, fuel pump

5 Related Answers

Anonymous

  • 702 Answers
  • Posted on Nov 10, 2008

SOURCE: having problems with my 96 chevy tahoe mass air flow

The MAF (Mass Air Flow) sensor is a very common problem with these along with the pickups. This isn't what you would call an inexpensive part. Definitely do some shopping before you buy one.

Ad
dennymulford

Dennis Mulford

  • 1055 Answers
  • Posted on Apr 16, 2009

SOURCE: I have a 2000 Chevy Blazer I have replaced

maf sensor, tps sensor,or timing gear

Anonymous

  • 34 Answers
  • Posted on Jun 20, 2009

SOURCE: 1997 chevy silverado 1500 350 vortech, new fule pump not working

before you drop tank again, check fuses & relay.then disconnect fuel line @ filter turn key to on position should hear fuel pump run and get gas stream out of line. if no flow from line new pump faulty be sure & remove negative battery cable first good luck.

brentfelz

  • 5 Answers
  • Posted on Oct 09, 2009

SOURCE: looking to findthe mass air flow sensor on a 89 chevy corsica

location is under the hood where the aircleaner is there is an electrical connection that plugs into the mass air flow sensor

Anonymous

  • 41 Answers
  • Posted on Dec 18, 2009

SOURCE: my van when pressing on gas pedal jerks while

could be two things, 1; the coil is going bad. 2; the electronic egr valve has a piece of carbon in it. the latter is probably the problem. to fix this , just remove the valve, push on the piston and while holding it in the open position, spray with carb cleaner and blow it out, release the piston and be sure the valve is closing all the way. if the gasket is damaged you can get a new one at the parts store.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My 2000 Chevy Silverado 4.3 6 cylinder is sputtering at about 2000 rpms. I did a tune up. Wires, plugs, pcv, EGR, distributor kit and air filter but still sputters.

Check engine light on ? Code's ? Scan data from a scan tool , MAF - mass air flow sensor , map , fuel trims , O2 sensor etc....
0helpful
1answer

Does a 2000 Chevy Silverado 1500 4.3 motor have a intake air temperature sensor

Yes it does, it is located between the mass air flow sensor and the intake, you shouldn't have any trouble finding it.
0helpful
1answer

Silverado mass air flow sensor

the map sensor could be the problem for code P0101
hope it helps
3helpful
1answer

2000 Chevy Silverado occasionally won't hold idle when starting

Try cleaning the throttle body and the mass air flow sensor.Does your check engine light come on?
0helpful
1answer

Air flow to defrost or floor not switching stays on dash vents

cannot switch from defrost to panel airflow 2001 chevy silverado
1helpful
2answers

My 2000 Chevy Silverado has trouble code P1133.

some cars do have recalls for bad codes being thrown check your dealership and if theres no problem they can block the code so your engine light will not come on for that code
0helpful
1answer

2000 Boniville bucks like a horse and trys to stall

that could be it. but it could be the timing too i think.. if you run the car and its hot when it starts to buck and stalls.. the rubber belt could be getting warm and expandig and causing it to slip out of timming just a hair.. then you let it set and cool down the belt then re-cools and runs fine. that or it could be just simple needing new wires and plugs. if they are mis firing and then the plug misfires completely it will cause the car to buck and stall out.. i personally would check wires and plugs then the distributor block make sure there are no mis firing there also.
10helpful
2answers

MAF sensor and injectors

the mass air flow sensor is located between the air filter housing and the air inlet to the intake manifold, remove the two band clamps holding the maf sensor, clean when cold with CRC mass air flow sensor,remember to take off the three wire plug to the maf sensor,get back to me if you need more help,please rate my fix as i strive to be the best,problems,get back to me
Not finding what you are looking for?

28 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...