Question about Cars & Trucks

1 Answer

What's (mil requested) mean?

I get a p0700 code which is the ****** but usually it is followed by other codes. What does Trans Cont Sys Mil Requested mean specifically?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,431 Answers

P0700 means transmission control fault detected,either it is mechanical or electrical.This code is a generic code,you will need a enhanced code that mean a manufacture scantool or a scan tool that can read enhance code.

Posted on Mar 29, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

chryslerguy

  • 323 Answers

SOURCE: 2002 caravan trans. no 3 or 4 gear

replace the input and output speed sensors

Posted on May 28, 2009

csmock132

Clint Smock

  • 4669 Answers

SOURCE: 2004 pacifica P0700 Transmission Control System (MIL Request)

You need to scan the tcm. Code p0700 in the ecm just tells you there is codes in the tcm.

Posted on Mar 12, 2009

Anonymous

  • 199 Answers

SOURCE: p1789 and p0700

you can get all the required parts at either the local garage this will be second hand. you can get this at the mitsubishi service center or at  www.autozone.com

Posted on Jan 05, 2009

saailer

David Burbee

  • 1871 Answers

SOURCE: Manufacturer Specific Code P1171

Change upstreamO2 sensor on bank #1



FixYaWIZ...saailer


I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Posted on Dec 10, 2009

Anonymous

  • 34 Answers

SOURCE: I have a 2005 Dodge Neon and the engine light came

a had the same problem. i am 99.9 percent sure that the wires going to the sensors underneathe the battery box and air intake are broke inside the insulation. Get to where you can see the connectors. remove the tape from both sensor connectors and give the wires a pull each wire done seperately. Mine was an orange wire and a purple wire. It is not noticeable by looking at the wires because it is the copper wire inside the insulation that will be broke. Find the broke ones and splice in new wire and the problem will be fixed.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2hat does code #P0700 mean on a 2007 Chevy Silverado. 4x4 mean


DTC P0700: Transmission Control Module (TCM) Requested MIL Illumination
DTC P0700 can not be cleared from the ECM until the related TCM codes have been cleared.

The transmission control module (TCM) uses the (GMLAN) to signal the engine control module (ECM) that the TCM is requesting malfunction indicator lamp (MIL) illumination. This happens when the TCM has determined that a failure affecting emissions has occurred in transmission control system. When the ECM receives the a message from the TCM, DTC P0700 will set.
You don't say which engine your's has ! Or which transmission .
Automatic Transmission - 4L60-E/4L65-E/4L70-E

You need to have TCM checked for codes .

Dec 22, 2016 | Cars & Trucks

1 Answer

I need info on locate the part for code p0700 trans. control system


The P0700 means Transmission Control System (MIL Request)
----------
WI-FI OBD AUTO CHECKER

Oct 12, 2012 | Cars & Trucks

2 Answers

Engine code p0700, p0871 and p0760


The P0700 means Transmission Control System (MIL Request)
The P0760 means Shift Solenoid "C"
The P0871 means Transmission Fluid Pressure Sensor/Switch "C" Circuit Range/Performance.
_________________
spare transponder key

Oct 05, 2012 | 2003 Dodge Intrepid

2 Answers

Check engine light indicates p700 code


Diagnostic Test Code (DTC) P0700 is an informational code that is stored in the Engine Control Module (ECM) That informs the diagnostic technician that there are codes present in the Transmission Control Module (TCM) and that the TCM has requested the Malfunction Indicator Lamp (MIL) (AKA - Check Engine Light) to be turned on. This is because the MIL is controlled by the ECM and cannot be turned on directly by the TCM. So, the TCM requests the ECM to turn the light on. To find out the nature of the failure that caused the P0700, one must scan the TCM to retrieve the fault codes stored there. Please note that MOST generic OBD code readers cannot access the TCM - this is the reason for the P0700 code to set in the ECM (to alert somebody with a generic code reader that further diagnosis is needed for the TCM).

Feb 16, 2012 | 2000 Jeep Cherokee

1 Answer

Code P0700


P0700 = TCU request for 'MIL' on (IE transmission control unit has detected a fault and wants you to know about it.)

Reasons:

A communication line exists between the Engine Control Module(ECM) and the Trans-axle Control Module (TCM). The sole purpose of this communication line is for the TCM to notify the ECM to activate the Malfunction Indicator Lamp (MIL) when a serious trans-axle failure has occurred.

DTC Description
If the signal "MIL ON" is requested from TCU or it is no signal from TCU, the ECM judged as a fault and DTC is set.

Kia's first suggestion is to check for damaged wiring or connectors.

Try this: Disconnect your battery for about 5 minutes to clear the fault. Then take it for a spin and see how it shifts... good luck.

Jan 11, 2012 | 2006 Kia Optima

1 Answer

Put trans in works great but has a code po 0700


P0700 is a generic fault code indicating a transmission problem. It's possible it's a left over code from the bad transmission you replaced. You may need to have the code cleared at a transmission shop that uses a different code reader to clear the code. Unfortunately, unlike the standard OBDII code reader, the transmission codes don't always reset themselves after a repair is made.

Oct 13, 2011 | 2000 Jeep Cherokee

1 Answer

Engine light on ,shows po700 trans seems to work fine


P0700 Transmission Control System (MIL Request)
It just means that the MIL is being requested, but there don't seem to be any other codes associated with it, so I wouldn't worry about it unless a driveability or fuel economy or engine/transmission performance problem arises.

Nov 12, 2010 | 2001 Chevrolet Silverado 2500HD

2 Answers

Have 2001 chevy 2500hd with a code 0700 bad tcm. can you tell me where it is and how much do they run.


P0700=Transmission Control System (MIL Request)
Does not mean bad TCM,=transmission control modual,
all that happen here was the computer did not like the responce it got from a sensor,and requested the check engine light be turned on.
You need to have it scanned by a shop if it reappears

Dec 25, 2009 | 2003 Chevrolet Silverado 2500HD

1 Answer

2004 pacifica P0700 Transmission Control System (MIL Request)


You need to scan the tcm. Code p0700 in the ecm just tells you there is codes in the tcm.

Mar 12, 2009 | 2004 Chrysler Pacifica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...