Replace electric motor for ford focus front window

The video at this link should give you what is needed to complete the job.

Try spraying some electrical contact cleaner into all of the switches on the main controll on the drivers door. With the vehicle running ignition on . It s likely just a bad connection water gets in between the window glass and the switches . If that dosn't work remove the main switch and clean the contacts and it will work again.

SECTION 501-11: Glass, Frames and Mechanisms 2003 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/24/2003 Rear Door Window Regulator and Motor Printable View (208 KB) Removal and Installation

1. Remove the rear door speaker. For additional information, refer to Section 415-03.

1. Remove the side impact bolster.

1. Position the door latch release handle aside.

1. CAUTION: Do not touch the adhesive surface, as re-bonding will be impaired.
   Remove the watershield.

1. Connect the window operating switch electrical connector.

1. Align the regulator clamp with the access hole.

1. Remove the window glass from the regulator clamp.
   1. Push out the pin.
   1. Push out the sleeve.
   1. Remove the window glass from the regulator clamp.

1. CAUTION: Make sure the window glass is adequately supported at the top of the opening.
   Using suitable hooks, raise and secure the window glass.

1. Disconnect the window operating switch electrical connector.

1. Disconnect the motor electrical connector.

1. Remove the bolts and the motor and window regulator.

1. To install reverse the removal procedure.

1. Remove the front door trim panel.
2. Remove the front door watershield.
3. Secure the front door window glass in the full upward position with tape.
4. Remove the front door window glass-to-regulator assembly bolts.
   • Loosen the glass clamp fasteners through the 2 vertical slots in the inner door panel.
   • To install, tighten to 9 Nm (80 lb-in) .
   1. Disconnect the front door window electrical connector.
   2. Remove the front door window regulator bolts.
   • To install, tighten to 11 Nm (8 lb-ft) .
   1. Remove the front door window regulator and motor.
   2. To install, reverse the removal procedure

The power windows are wired to a window relay. No fuse is linked to the window motors or switches

First you will have to remove the door panel to access the window motor which is located in the door. in most cases you are better off to replace it. but first you need to check for power at motor if it has power and doesn't work replace it if no power check the switch then check wire in the door jam they usually break from excessive opening and closing of the door .

Removal & Installation
Motor - Front Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the window control switch
3. Remove the front door trim panel and watershield.
4. Tape the window in the full UP position.
5. Disconnect the window motor electrical connector.
   NOTE Support the window motor while removing the window motor retaining screws.
   
6. Remove the window motor bolts and remove the motor.
7. To install, reverse the removal procedure.

Rear Door

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the window control switch.
3. Remove the rear door trim panel and the rear door trim watershield.
4. Remove the door speakers.
5. Tape the window glass in the full UP position.
6. Disconnect the window regulator electric drive.
7. Position the connector for the window regulator electric drive inside of the door.
8. Remove the bolts.
9. Separate the window regulator electric drive from the rear door window regulator.
10. Remove the window regulator electric drive from the door.
11. To install, reverse the removal procedure.

Motor & Regulator



Fig. Front Door Trim Panel




Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows



Fig. Window regulator arm nuts




Fig. Window regulator bolts

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove the window control switch.
3. Remove the door trim panel.
4. Remove the door speaker.
5. Remove the door watershield.
   NOTE Do not remove the window glass from the door.
   
6. Remove the window glass from the window regulator.
7. Tape the window glass in the full UP position.
8. Disconnect the window motor electrical connector (power windows only).
9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
10. Loosen the bolts and remove the window regulator.
11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the front door trim panel screws.

1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
   Remove the front door trim panel.
   • Disconnect the electrical connectors.

--------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation

1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.

1. Disconnect the front door window regulator motor electrical connector.

1. Remove the window regulator rivets.

-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation

1. Close the window.

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the door trim panel. For additional information, refer to Section 501-05 .

1. If equipped, remove the radio speaker.

1. Position the watershield aside.

1. Disconnect the door window regulator motor electrical connector.

1. Remove the bolts and the door window regulator motor.

---------------------------------------------------

most likely the electric motor that raises and lowers the window is defective, u will need to remove the door panel and replace the window motor, about a 2 hour job and $100 in parts.

you will need to drill out some rivets. Replace with ntus and bolts and washers & lock washers. Make sure they don't hit glass going up and down. Otherwise you will need a heavy duty riveter.
please rate as fixya if this helps.

Motor —Front Door
Special Tool(s) Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal
NOTE: The window regulator and motor are removed as an assembly.

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the front door radio speaker.

1. Remove the latch remote control. For additional information, refer to Section 501-14A .

1. Remove the front door watershield.

1. CAUTION: Support the window glass to avoid damage.
   Raise and support the front door window glass to the full up position.

1. Disconnect the power window motor electrical connector.

1. Remove the window glass to regulator nuts.

1. Remove the motor and window regulator assembly.
   1. Drill out the rivets.
   1. Remove the motor and window regulator assembly.

1. NOTE: Prior to motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind.
   Remove the power window motor.
   1. Remove the bolts.
   1. Remove the power window motor.