SOURCE: programming instructions for a 1999 Chrysler 300M remote fob
Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of
the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When
programming is complete, the door locks will cycle once.
NOTE:
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF
PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.
6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.
SOURCE: I need a free owners manual for a 2000 chrysler 300M
There will be a few minor differences between the 2000 and 2004, but for the most part, you can use the 2004 manual as a reference. Since it is illustrated, you can confirm visually when you are taking on repairs. I have owned a 2000 300m for several years. Might I recommend you visit 300mclub.org? I am a member there and have learned a ton about 300m's.
SOURCE: headlight bulb replacement on chrysler 300m
Parts Required: Change all the lights at once, it is not worth the
anguish of doing this over and over again
2 low-beam lights, 2
high-beam/running lights, 2 parking lights - part nos in the owners
manual
A can of diet coke to clean the battery terminals is
also recommended. *optional
Tools required
Ratchet set : 10mm, 7mm, 6mm sockets
Extension 12"
Large Flat
screwdriver, small 4" flat screwdriver and a pair of pliers
Flash-light
12" Magnetic tip telescoping bit
Surgical
gloves
Battery terminal cleaner * optional
Step
1:
First take off the plastic cover that cover that is
across the front of the engine compartment. 6 push pins hold it in
place, Use the long flat screw driver to pry them up and use the pliers
to pull them off.
Gently take the plastic cover off and set
it aside.
Step 2:
Next you will see 3 push pins
that hold the front grill to the engine housing, using the long flat
and a pair of pliers pull the 3 push pins out.
Step 3:
In
the upper area of each wheel well, you will see a large 2.5" rubber
grommet. Pull the rubber grommet out
Step 4:
Locate
a 6mm bolt head that is driven vertically upwards. It is not visible
looking at the wheel well. You have to lay down on the floor and you
will find it about a foot below the grommet and at the edge of the
fender. Use the the ratchet to remove this bolt headed screw. It is
about a 1.5" long. Do this for both sides before going to the next step
Step
5:
Start with the passenger side as it is easier. Use the
flash light and peer into the fender area from the engine compartment.
You will see a nut on a bolt, and a plastic fastener.
Use the 10mm
socket on the 12" extension. Insert it into the hole where the grommet
was, and guide the socket on the nut head. It is about an 1" long. Be
careful as you take it off, else you will be fishing for the bolt in the
fender.
Step 6:
Pull on the plastic fender in the
front till the bolt head and the fastener exit the fender. This has to
be repeated for each side.
Step 7:
Locate 8mm bolt
heads on top of the light assembly. Note it is not the Philips head -
they are to level the lamps. Before undoing the bolts, check the spirit
level on top of the lamp assembly and make a note of the bubbles
position. You will need this when you put the assembly back. Undo both
bolts, they have about an 1" of thread on the top and then you have to
pull it up physically or with the use of the pliers
Step 8:
Pull the headlight assembly out - gently. Don't scratch the paint work
and don't damage the rubber molding around the light assembly.
Step
8a*: If you see any salt build up on the battery terminals, pour
diet coke or pepsi on the terminals, this neutralizes all the salt. Then
pour some water to clean the gunk and then with a paper towel dry it.
Be careful with the paper towel, as it contains sulfuric acid and is
corrosive, put in in a garbage bag immediately. If you feel it has come
into contact with your skin, was vigorously before continuing.
Step
9:
Note the position of the connector before you do anything.
Turn the retaining rings holding each bulb counter clock wise. When you
do this the bulb assembly and the connector will pull free. Two
instances of this. Remove assembly, and place securely on a table
Step
10:
Locate the parking light below and turn the connector
clockwise as you are looking over it. Pull out the old bulb and replace
it. Do this for both sides. Turn on the parking lights to ensure they
work, try the signals too. No sense it putting it all back together and
nothing works. Replace the holder and bulb in reverse order. Note the
unit should fit in nicely and rotate smoothly as you turn counter
clockwise this time.
Step 11:
Using the 4" flat
screwdriver, lift the locking pins gently and push the bulb out, Start
with the low beams. Low beam has only 1 filament, high-beam/running
light has 2 filaments. Put on the pair of surgical gloves, and open the
pack of new bulbs, push the bulbs into the empty sockets, until the
locking pins click into place. Change the low-and high beams.
Step
12:
Insert the bulb with the connector in the position you
noted in step 9. Slide the mounting ring and then lock it into place by
turning it clock-wise as you are looking at it from the rear of the
assembly. Repeat this for both the high beam and low beam. Slide
assembly back into cavity. Repeat this for the other side. Test the
bulbs light correctly
Step 13:
Gently push back the
front plastic so that the bolt and the plastic stud enter the fender.
Pay attention to ensure that the fender lining sits correctly. Using the
12" ratchet extension and the 10mm socket mount the bolt back on and
tighten. Do this for both sides
Step 14:
Using the
ratchet mount the 6mm fastener on to the fender. Do this for both sides
Step
15:
Mount the jack screws on top of the headlight assembly.
Tighten till the bubble in the spirit level returns to the original
position. Don't push the bolt past its maximum. If it doesn't return to
the original level, loosen and adjust the headlamp assembly and
re-tighten. Do this for both headlamps.
Step 16:
Replace the 3 push pins that hold the front grill to the engine
compartment. Replace the large plastic panel that was removed in step 1
and remount it using the 6 push pins.
Voila - you have
changed all the bulbs on the front of the 1999 300M.
Estimated
time:
Novice 2 hours
Advanced 1 hour
Expert 45 mins
If you found this helpful, a quick note to the author George and Anna
at [email protected] would be appreciated.
SOURCE: 2000 chrysler 300m
The 700 is the limp mode, as I recall. One or both of the sensors are failing, and they are not too expensive to replace. Once replaced, then using the OBD tool, you can delete the fault codes and then be able to shift into all the gears.
I have written about this solution in other blogged questions, and so have others. Under the car, on the Driver side of the transmission are two electric sensors. They lay horizontally on the trans just behind where your foot would go on the accelerator and under the floorboard. The electricl clip sockets pull out with thumb pressure on each socket. DO NOT pull on the wires EVER. Unplug each socket, and replace one at a time. Use a 1" deep well socket and unscrew them from the side of the trans casing. Do one at a time starting with the one on the left, the Input side,; Then the output side.
The reason why I replace them both is that they are cheap- about $20 apiece- and REALLY: do you want to go under there twice for twenty bucks? If so, then just replace the one on the LEFT- the Input sensor. You then MUST RESET THE CODES with the OBD tool for the transmission side of the tool, then GO!
174 views
Usually answered in minutes!
i dont need to change the bulb i need to change the whole headlight assimbiley.
×