Question about 1999 Dodge Stratus

2 Answers

99 stratus 2.5 v-6/no spark.will crank over.

No spark.will crank over.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

CRANKSHAFT POSITION SENSOR - 2.5L

REMOVAL
  1. Remove speed control servo from driver's side strut tower.
  2. Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
  3. Pull crankshaft position sensor straight up out of the transaxle housing.
  4. (Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.
NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer
  1. Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
  2. Connect crankshaft position sensor electrical connector to the wiring harness connector.
  3. Attach connector to heater tube bracket.
  4. Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

Posted on Dec 31, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,468 Answers

Crank shaft position sensor

Posted on May 20, 2012

  • philathompso
    philathompso Nov 03, 2012

    mike, whats the best way to get to that sensor, it's looking like the air plenum needs to come off if doing it from the top

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My dodge stratus 2005 turns over great but will not crank any help


Pull a plug wire or coil and check for spark. No spark look to the crank sensor. Check fuel pressure.

Sep 03, 2016 | 2005 Dodge Stratus Sedan

1 Answer

2001 dodge stratus 2.4 dohc will the coil pack spark if the valves are bent on the number 2 and 3 cylinders


If the engine cranks, and the cam and crank are close to being in time, the coils should fire.
You just would not have compression on some cylinders.

Mar 25, 2015 | 2001 Dodge Stratus

3 Answers

2001 dodge stratus 3.0l automatic cranks but wont start not even with start fluid


check the fuel pressure and make sure you got the correct pressure

Jan 25, 2014 | 2001 Dodge Stratus

1 Answer

Car stopped will not start is cranking over is there a coil pack on 2000 dodge stratus


yes there is a coil pack, check for spark be inserting a screwdriver in on ov the spark plu wire's and ground it out to the block and have somwhone crank the motor over, if u have spark, it might be the fuel pump or related part's

Jun 05, 2010 | 2000 Dodge Stratus

1 Answer

I replaced the fuel pump and filter in a 99 dodge stratus and it still wont start what can I try to fix it?


Hi,
When you turn the key to "on" (not to crank), listen to determine if you can hear the fuel pump. If you can't hear, you might have someone outside the car and near the gas tank, listen closely as you do this. It's possible the pump isn't working... though you replaced it.
If you're getting fuel, try to determine if you're getting spark at the plugs.
Hope this helps... a little.

Oct 13, 2009 | 1999 Dodge Stratus

1 Answer

99 dodge stratus dies while driving


Were the plugs covered in oil? With the plugs that go through the valve cover you might need new seals. Did you replace the plug wires? You need to scan it for codes. It's most likely a missfire, but it could be a bad speed sensor (also called, VSS vehicle speed sensor, cam position sensor,or crank position sensor).

Jul 27, 2009 | 1995 Dodge Intrepid

3 Answers

I have changed the timing belt on a 99 Dodge Stratus with a 2.4 liter engine. All timing marks are aligned properly according to Haynes diagram and the engine will still not start. It tries to start


check your distributor position,double
check all marks again,make sure when u line up
the crank marks at #1 cyl. at compression and cam shaft marks!!

G

May 28, 2009 | 2001 Dodge Stratus

1 Answer

2004 stratus won't start


try checking the fuel pump or replace the spark plugs and wires because most dealers put cheapos on them

Dec 05, 2008 | 2004 Dodge Stratus

1 Answer

Engine willnot crank


You will need to check for a crank signal at the starter solenoid.

Oct 15, 2008 | 1999 Dodge Stratus

Not finding what you are looking for?
1999 Dodge Stratus Logo

875 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...