Someone hit my car overnight. Broke the tie rod, so my wheels no longer turn when I turn the steering wheel. what's this on a novice level from say 1-10? I can change brakes, change oil, tear off a door, the real basic stuff. Now im looking at this tie rod broken, and it doesnt seem that hard. But looks can be deceiving~ before I get into it, thought I might get some advice. What might this cost in a repair shop?
you need to remove the nut allway then screw back on and hit the to or the coupling area, this will release the shaft so you don't get hit by the rod. do this on both ends, when removed measure the length of the rod, if its the same make as the one replacing count the treds and put the new one to the same length, this will keep your tracking in line as much as possible, then tighten the nuts. and fit. push the shaft into the original hole and tighten down with the nut, its always best to do both times when they are replaced, as they would both take the impact and the impact of the road. should only take a novice a couple of hours to do both sides, if steering out i would recommend getting the tracking done as the accident could of move other parts out of alignment.
SOURCE: how to change oil transmission isuzu rodeo 2003
There are two drain plugs on the bottom of the pan. remove the lower one to drain the trans fluid. To refill, use a pump and pump the fluid into the upper drain plug until it seeps out and re-install the plug, similar to refilling a manual trans.
Once this is done, Start the vehicle and run it for about 3 minutes, shifting through all gears (do not drive vehicle Remove the upper drain plug and let any excess fluid drain out. Done. This is as per Mitchell OnDemand.
SOURCE: 4 wjheel drive problem
not transfer case motor....there is none on a rodeo....trooper has torque on demand.....rodeo problem is likely shift on fly mtr...mounted on front axle....if u dont use 4wd regularly it sticks and gets stuck.
SOURCE: 1995 isuzu rodeo hood release broken under the hood
if the grille screws are accessable remove the grille which should give you access to the underside of the lock, you may need a screwdriver to push the lever aside to release the hood
Hope this helps
SOURCE: i'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.
1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)
2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)
3. Measure the oil clearance between the connecting rod and the crankshaft.
SOURCE: My automatic 96 isuzu rodeo no longer engages in
Hahahaha!... Seriously....!?!?! First off don't try to use a scan tool. The 4WD system isn't integrated into the OBD system. You won't get any codes related to 4WD.
Most likely the problem is defective shift solenoids. There are two shift solenoids which control the engagement and disengagement of the 4WD (locking the front axle gear into the the driveshaft input). These solenoids are located on the front axle. They have their own small skid plate. One is blue, and one is gray. One controls engagement, and one controls disengagement. One is a normally closed electrically controlled vacuum solenoid, and one is a normally open electrically controlled vacuum solenoid.
I'm not blindly recommending changing these, but usually one of these are the culprit of the problems you described. I'm even more confident in those being the problem due to your explanation of the the intermittent problems. At any rate test first.
The other components of the 4WD system are the vacuum lines and the actuator which is also located on the front axle and covered by the forementioned small skidplate. Moderate to serious rock-involved off-roading with a stock suspension usually results in this component being damaged.
134 views
Usually answered in minutes!
×