Hi, The key fob stopped working all of a sudden. I replaced the battery and tried. but it is not working. I tried the options available in the internet but still no luck. Pl provide me some inputs on how to reset it.
Have you tried replacing the rubber pad buttons? We had the same problem. The remote quit working and we changed the battery and it still didn't work. I was actually online looking for a replacement and came across something about the the rubber pad buttons. We ordered a replacement for $9.95, it came two days later and was a cinch to change out. The remote has been fine, ever since.
SOURCE: need to reset the key fob after replacing the
You should not have to reset the key fob after a battery replacement. The signal from the key fob stays the same and is programed to the reciever.
If the key fob needs to be reprogrammed then follow these steps.
1. Have all key fobs with you during programming.
2. Sit in the vehicle with all doors closed.
3. Lock all doors using the Lock/Unlock switch on the door.
4. Insert and withdraw the ignition key 7 to 9 times within 10 seconds (do not turn the key, just insert and withdraw).
5. The 4 way flasher indicator on the dash should flash once or twice.
6. Insert the ignition key and turn it on (key on, engine off).
7. Press any button on one remote and the 4 way flasher indicator on the dash should flash once.
8. If you have more key fobs to program use the Lock/Unlock button on the door to unlock the doors and then lock the doors.
9. Press any button on the next key fob and the 4 way flasher indicator on the dash should flash once.
10. Repeat if you have more key fobs. Only 5 can be programmed.
11. To exit, simply turn of the igniton and remove the ignition key.
12. Unlock the doors using the Lock/Unlock switch on the door and exit the vehicle.
13. Make sure the window is down when testing remotes in case you leave the keys inside.
14. Close all doors and test all remotes that were programmed.
Do not skip any steps or the process will not work.
If the 4 way flasher indicator does not work when inserting the key, you will need to start the process from the begining. If it still does not work the receiver may be your problem.
If the 4 way flasher indicator does not flash when pressing any button on the key fob then the key fob is the problem (dead battery or defective remote)
SOURCE: where,s the key hole
Go to the front passenger side door and prise off the rear section - on close inspection you will see that it has a key symbol on it, the key hole is underneath.
SOURCE: I need to somehow reset my factory alarm on my 1995 Nissan Maxima
this is how most nissans program the key fobs.
get in the car and manually lock the drivers door with the door switch.
put the key in and out of the ignition about 10 or 12 times until the hazard lights flash once.
turn the key to the ignition setting so all the dash lights are on,but do not start the car.
click the lock button on the remote fob.the hazards should flash once to confirm.
turn off ignition and remove the key.
unlock the drivers door and open the door.
the remote should now work.
if that does not work,the dealer can reprogram the fob with the obd diagnostic system.
SOURCE: Hi I want to program a new keyless fob. I have
1. Close and lock all doors with the driver’s side power lock/unlock switch.
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.
3. Insert key into the ignition cylinder and turn to the ACC position.
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.
SOURCE: How do you program a key fob / transmitter for a 2009 Altima?
all keys/car have to be programmed at the same time.using nissan diagnostic machine.you could try a quickfit centre (if they have correct machine)
1,255 views
Usually answered in minutes!
×