Question about 1999 Jeep Wrangler

1 Answer

I own a 92 jeep wrangler 4 cyl 2.5L. my jeep sputters like it wants to turn off. sometimes it does turn off it will turn off while im driving and or stopped. ive changed the plugs the wires and crank position sensor twice in one month problem continues i ve replaced the crank position sensor twice in one month. fixes the problem for a short time then it starts again.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Jeep Master
  • 614 Answers

When it tring to shut down lift igintion switch key

Posted on Sep 14, 2017

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Bill Hackett

  • 383 Answers

SOURCE: jeep wrangelr Crank Position Sensor

wall5552: there were two engines used in 1992 Jeep Wranglers.
A 2.5 liter and a 4.0 liter. HOWEVER>>>> The location for the crank angle sensor is the same for both.
It is located on the bell housing up near the front at about the 10:00 PM position.
The Cam position sensor is located in the Distributor on both engines as well.

Posted on May 10, 2009

Mikey108

Michael Zangari

  • 475 Answers

SOURCE: 1998 jeep wrangler P0122

ck the map sensor

Posted on Sep 16, 2009

kingandrew01

  • 13 Answers

SOURCE: I have a 97 grand

You did reset your timing after all te new parts correct? If not start there. Also if it still give the crank postistioning sensr as your error then you may have it pluged in wrong(i know, i know! Ive seen it happen though), or perhaps there is a problem with that circut and your ECM. But i do think you have first off.

Posted on Apr 17, 2011

long27574

Richard Long

  • 103 Answers

SOURCE: 92 jeep wrangler 5 spd 4 cyl skipping and bogging

Replace the catalyst convertor. When a convertor goes bad, the guts of it break apart and end up clogging the exit port. One of its functions is to remove toxins from the air. Helps the emission system to run rich or lean gas exhaust.

Posted on May 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, I'm looking for a replacement for my jeep cherokee 99, the current part number is Chysler P56041 629AD, I found a Chysler P56041 278AD, can this computer works ok with my cherokee?


THE PCM MODULE.
no country stated, the 728ad shows Europe. (why?)
"I found"

where, at ebay, at pick-apart, or ?
USA cars have 11 PCM for one engine. fact.
and 100s more world wide.
what a question, just a p/n
then you post to grand Cherokee and then text leaving out Grand.?
why?
i searched the part at jeep and is wrangle part, 629ad.

you do know that it must be reprogrammed to your car right:?
the pcms on cars can vary
by engine, trans opted , 4wd/2wd,and year.
federal PCM
Calif PCM
and mexico PCM
and 9 more. just for 1999

is yours 42RE for 45RFE?? tranny??? 30/32 RH? what?
post county (or state if calif)
post engine and year
post body and not contradict.?
post drive line, in car, tranny and if 4wd?
then we can match it up
or call jeep.com

they (jeep) will do this magical thing!
ask you the VIN.
and then look it up in their database.
and see ALL THE ABOVE even what radio is in it. of 5.
me, im a glass half full guy (hard knocks, reality stuff)
id not even believe the part in car is correct.
im too SAVVY !
i find out from jeep what it should have first.

not one matches the 4.0L in the GC.


the 629 posted shows this at jeep.com

JEEP WRANGLER 2.5L Power Tech I-4 Cyl., 3-Spd. Automatic 30RH 1998
JEEP WRANGLER 2.5L Power Tech I-4 Cyl., 5-Speed Manual 1998
JEEP WRANGLER 4.0L I6 Power Tech, 3-Spd. Automatic 32RH 1998
JEEP WRANGLER 4.0L I6 Power Tech, 5-Speed Manual 1998
(if true needs to be programmed to each)

the send number
56041 278AD

lands at.
(part not found, is this a non usa part?) im stumped

was fun to try.
but im stumped.

Mar 31, 2016 | 1999 Jeep Grand Cherokee

1 Answer

92 jeep wrangler 5 spd 4 cyl skipping and bogging down replaced timing chain distributor plugs wires injector o rings cleaned out fuel tank new map sensor and new crank sensor sometimes it runs fine but...


Replace the catalyst convertor. When a convertor goes bad, the guts of it break apart and end up clogging the exit port. One of its functions is to remove toxins from the air. Helps the emission system to run rich or lean gas exhaust.

May 06, 2012 | 1992 Jeep Wrangler

1 Answer

THE TRANSFER CASE WILL NOT ENGAGE IN 4H OR 4L. IT IS A 92 WRANGLER 4.0 6 CYL. WHAT IS THE PURPOSE OF THE VACUMM HOSES. BEFORE THE CASE IS REMOVED WHAT TROUBLESHOOTING SHOULD BE ACCOMPLISHED FIRST.. THANK...


4 wheel drive is vacuum activated. Check vac motor 1st as it is probably the reason for it not engaging. I had a 88 cherokee w/ bad vac motor which caused exact problem you describe.

Jul 14, 2009 | 1992 Jeep Wrangler

1 Answer

98 jeep wrangler 4.0 6 cyl. sputtering/near stalling all speeds


hi april, it sounds like the camshaft position sensor is failing!...question?, does your temperature gauge work normaly?, is there any check engine lights on? if so let me know the code number and i can help ya! good luck, marty

Jun 04, 2009 | 1998 Jeep Wrangler

1 Answer

92 Jeep Wrangler will not Stay running.


I had the same prblm with my 1989 Jeep, 6 cyl straight, and it was because of the EGR valve, easy to replace and not too costly. EGR valve is screwed on the motor, driver side, and there is a ±1/2" rubber hose attached. Easy to see if device comes apart, cut by rust.

Mar 18, 2009 | 1992 Jeep Wrangler

2 Answers

97 wrangler 6 cyl ck eng lite just came on light


first you need to find out the code auto zone or advance auto should give you a code reading , i try to help but without the trouble code im lost

Dec 19, 2008 | 1997 Jeep Wrangler

Not finding what you are looking for?
1999 Jeep Wrangler Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...