2002 Kia Sportage Logo

Related Topics:

James Zifchock
James Zifchock Posted on Jan 22, 2018
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

2002 kia sportage crankshaft pulley has one flat drive groove and two v grooves but the a/c unit appears to have flat drive belt Kia parts looked up the Vin# matched it with the correct pulley, same one replaced on the vehicle. But the A/C has a flat belt not v groove as the pulley is. What gives.

Answer This Question

1 Answer

matt

matt

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Kia Master 1,666 Answers
  • Posted on Feb 10, 2018
matt
Kia Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Sep 16, 2009
Answers
1666
Questions
4
Helped
695805
Points
9998

5 Related Answers

Anonymous

  • 36 Answers
  • Posted on Jul 26, 2009

SOURCE: where is crankshaft sensor on 99 kia sportage?

The crankshaft pos. sensor is located on the left "driver" side of the engine on the bellhousing and is retained by a single 10mm bolt.The sensor may be tight,be sure to twist as you pull so that it doesnt break off in the bottom end.

Ad

Jonah Oneal

  • 14092 Answers
  • Posted on Aug 23, 2009

SOURCE: 2005 Kia Sportage serpentine belt

YOU NEED THE BELT TENSIONER TOOL ITS FITS IN THE SQUARE SLOTS IN THE TENSIONER.YOU ROTATE TENSIONER CLOCKWISE TO REMOVE BELT.

Anonymous

  • 117 Answers
  • Posted on Sep 27, 2009

SOURCE: 2002 kia sportage airbag light flashing 1 -3 code,

first thing to check, how is your battery? Are the battery posts clean? next check your fuses. replace as needed. sometimes if an aftermarket stereo has been added, the wront power cord may have been splice. need to get the exact coce and find out what it means. i have never heard of a 1-3 code, usualy there are in the form of T0222 or T444 or something close to that.
hope this helps a bit, the actual error code would help quite a bit

anderza

anderza

  • 41 Answers
  • Posted on Jan 07, 2010

SOURCE: Timing belt broke on my kia sportage...

Check solutions for Kia Sportage under heading. Need timing marks and ignition wiring by Brattlehead. The markings I gave him will also work for your 2001 Sportage

JOSHUAJBARTH

  • 57 Answers
  • Posted on Jul 12, 2010

SOURCE: 2002 KIA SPORTAGE OWNERS MANUAL

GO TO ONLINEFREEEBOOKS.NET SHOULD BE A PDF

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How to install a serpentine belt on a 2001 Volkswagen Passat
there are 15 serpentine diagrams for the belt on vw engines to 2001
some have no ac , power steering etc
need engine size
you could try this the grooves are for driving pulleys so any grooved pulley it has to go around
flat pulleys run on the back of the belt so they will be idler pulleys
start at the crank and work to the left if there is a flat pulley between two grooved pulleys the back goes around it and so on
Read full answer
Jul 15, 2017 • Volkswagen Cars & Trucks
0helpful
1answer

Where is the tensioner pulley located on a 2011 Kia Sorento
Remove any items that may hinder you from looking at the drive belt and all pulleys that hooked up to it. The tensioner pulley is different from other pulleys as it has no grooves on it. It looked just like a roller with flat outer surface. It pushes on the flat side of the belt (compared to the grooved side -as other pulleys did). It is spring loaded and can be de-tensioned by moving it in the reverse direction of its push. If you are looking the TIMING BELT tensioner, then more things have to come off the engine before you could get to it.
Read full answer
Dec 28, 2016 • 2011 Kia Sorento
0helpful
1answer

I have an 89 Toyota Camry 4 cylinder and I need to know what belt this is.
your photo is not good so I will give a generic answer
it is the drive belt for the accessories on the engine ( water pump, alternator .ac compressor ,power steering pump
if it "V" shaped it is a V belt
if it is many grooved it is a serpentine belt
the difference is that "V" belts only flex around a pulley where serpentine (grooved ) belts have the grooves around some grooved pulleys and the back runs around flat pulleys
it is not a timing belt
Read full answer
Nov 19, 2015 • Toyota Cars & Trucks
0helpful
1answer

Causes of serpentine belt tensioner failure
seized bearing on one of the units being driven
incorrect fittment of the belt where the back of the belt is running over grooves and the grooves in the belt are running over flat surfaced pulleys
misalignment of pulleys
Read full answer
Nov 07, 2015 • Cars & Trucks
0helpful
1answer

What is the pattern of the front drive belt
an engine /vehicle model with information of power steering and ac fitment would help. Basically the grooves in the belt go into the grooves of the pulley and any idlers run on the back ( flat) part of the belt. If you have grooves in the belt running over a flat idler pulley then the belt is fitted wrong.
Read full answer
Nov 13, 2014 • Cars & Trucks
0helpful
1answer

Please could you give me a diagram of the valve timing of a double O.H.C.on a toyota Rav4 3SFE engine
no year(94-present) stated. and under kia dont help much.

its at alldtata.com, i read all the steps and not skip one, I WOULD.

wild guess, #1 a 2005 RAV4
2.0L 3sfe. inline 4 cylinder, not V6


here is the one i see on the FSM.

my gates belts all come with a manual. RTM?
if you buy the belt at a dealer they assume you have the FSM.
right?
FSM, install, steps
  1. Install the oil pump pulley. Tighten the nut to 18 ft. lbs. (24 Nm).
  2. Install the crankshaft timing pulley. Align the pulley set key with the key groove of the pulley. Slide on the pulley facing the flange side inward.
  3. Install the No. 2 idler pulley and tighten the mounting bolt to 31 ft. lbs. (42 Nm). Be sure that the pulley moves smoothly.
  4. Install the No. 1 idler pulley with the bolt and the tension spring. Pry the pulley toward the left as far as it will go and tighten the bolt. Make sure that the pulley moves smoothly.
  5. Temporarily install the timing belt. Using the crankshaft pulley bolt, turn the crankshaft and position the key groove of the crankshaft timing pulley upward. If reusing the timing belt, align the points marked during removal.
  6. Install the timing belt on the crankshaft timing pulley, oil pump pulley, No. 1 idler pulley, water pump pulley and the No. 2 idler pulley.
  7. Install the timing belt guide.
  8. Install the lower (No. 1) timing belt cover and new gasket with the 4 bolts.
  9. Align the crankshaft pulley set key with the pulley key groove. Temporarily install the crankshaft pulley and bolt.
  10. Align the camshaft knock pin with the groove of the pulley, and slide the timing pulley onto the camshaft with the plate washer and set bolt.
  11. Tighten the pulley set bolt to 40 ft. lbs. (54 Nm).
  12. Turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  13. Finish installing the timing belt and check the valve timing, as follows:
    1. If reusing the old timing belt, align the matchmarks made previously and install the timing belt onto the camshaft pulley.
    2. Align the marks on the timing belt with the marks on the camshaft pulley.
    3. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    4. Turn the crankshaft pulley 2 complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    5. If the No. 1 idler pulley uses a green tension spring, slowly turn the crankshaft pulley 1 7 / 8 revolutions, and align its groove with the mark at 45 degrees BTDC (for the No. 1 cylinder) of the No. 1 timing belt cover.
    6. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    7. Be sure there is belt tension between the crankshaft and camshaft timing pulleys.
  14. Place the right-hand engine mounting bracket in position but do not install the bolts.
  15. Install the upper (No. 2) timing cover with a new gasket(s).
  16. Remove the engine crankshaft pulley bolt and pulley.
  17. Using SST 09249-63010, or equivalent, install the mounting bolts for the right-hand mounting bracket. Tighten the mounting bolts to 38 ft. lbs. (52 Nm).
  18. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  19. Install the spark plugs.
  20. Install the right-hand mounting insulator, as follows:
    1. Attach the mounting insulator to the body and mounting bracket with the 4 bolts and 2 nuts.
    2. Tighten the 3 bolts to hold the mounting insulator to the body. Tighten the bolts to 47 ft. lbs. (64 Nm).
    3. Tighten the 2 nuts and bolt to hold the mounting insulator to the mounting bracket. Tighten the bolt to 27 ft. lbs. (37 Nm) and the nut to 38 ft. lbs. (52 Nm).
  21. Install and adjust the power steering pump drive belt.
  22. Install the right-hand engine undercover.
  23. Install the right front wheel.
  24. Lower the engine.
  25. If equipped, install the ABS actuator.
  26. Install the alternator and alternator bracket.
  27. Install the wiring harness bracket for the DLC1.
  28. Install the power steering reservoir bracket and reservoir.
  29. Connect the negative battery cable.
  30. Start the engine and check the timing.

step 13.4 is never to be skipped. ask why., most do. and it fails.






a70ecb7d-3231-4383-bdd9-edd2200c74a4.jpg
Read full answer
Jun 07, 2014 • 2002 Kia Sportage
0helpful
1answer

What would make a belt fall off a 2007 ford fussion or split the belt into?
The split is puzzling. But for falling off, the tensioner must be weak. The pulleys can wobble if the bearings in their center is bad, you will be able to feel roughness.

The tensioner arm is spring loaded. Sometimes there is a wear bar for judging if a belt is stretched. No matter how strong a tensioner spring is, if the belt has stretched too far, there is nothing you can do but replace the belt.

Check the pulley grooves and count them. Some Alternator pulleys have 8 grooves and some have 6 grooves. While the flat faced pulleys are often wider than necessary, the grooved pulleys can quickly cut a wider belt into 2 belts. The Alternator grooves must match the number of grooves on the crankshaft.
Read full answer
Feb 25, 2014 • Ford Fusion Cars & Trucks
0helpful
1answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L
To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif
Read full answer
Jul 03, 2010 • Cars & Trucks
0helpful
1answer

Nned to know how to set the cam and engine timing
Start with crankshaft pulley. At the rear of the pulley is a notch. Align it with the mark on the oil pump.(No 2 piston is at TDC) There is also a groove on the pulley that needs to be aligned with the white dots on the cambelt. The lettering on the belt must be readable as viewed from the front of the vehicle.
(When seated in the vehicle the RH bank of the engine is on the RH side of the vehicle.Keep this in mind)
At the front of the camshaft pulley is a groove. Rotate the RH bank camshaft pulley to align this groove with the mark on the cylinder head cover. On the cambelt is a white line. This must also align with these marks. Do the same on the LH bank. To be sure the cams are now correctly aligned remove the cylinder head cover. On the camshaft drive gears the letters RI(Right intake) and RE(Right exhaust) will be at the top and readable for the RH bank. (For the LH bank it will be LI and LE) Reinstall the tensioner and rotate the crankshaft with a wrench to make sure there is no unintentional mechanical contact.
Read full answer
Dec 10, 2009 • 2002 Isuzu Rodeo
2helpful
1answer

Cant find 97 ford taurus serpentine belt diagram
Drive Belt Replacement ani_caut.gif WARNING: IF EQUIPPED, DO NOT ALLOW DRIVE BELT TENSIONER (6B209) TO SNAP BACK AS DAMAGE TO DRIVE BELT TENSIONER OR PERSONAL INJURY COULD RESULT.
NOTE: Minor cracks in the V-grooved portion of the serpentine drive belt (8620) are considered normal and acceptable. If the drive belt has chunks missing from the ribs, the drive belt should be replaced.

NOTE: Conditions requiring drive belt replacement are excessive wear, rib chunk-out, severe glazing, frayed cords or other conditions. Replace any drive belt exhibiting any of these conditions.

NOTE: When installing drive belt on pulley, make sure that all V-grooves make proper contact with pulleys.



q1834c.gif

Drive Belt, Serpentine—Except SHO
Removal
  1. ani_caut.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE THAT TOOL DOES NOT SLIP FROM DRIVE BELT TENSIONER OR PERSONAL INJURY AND/OR DAMAGE TO DRIVE BELT TENSIONER AND DRIVE BELT MAY OCCUR.
    Using a 15 mm socket or wrench on bolt attaching drive belt tensioner pulley, rotate drive belt tensioner clockwise on 3.0L (2V) and 3.0L (2V) FF, rotate the drive belt tensioner counter clockwise on 3.0L (4V) to remove drive belt from pulleys. Make sure spring keeper engages into slot.


    Drive Belt Tensioner—3.0L (4V)


    q3759a.gif

Installation
  1. Install drive belt over all pulleys (except drive belt tensioner).
  1. Rotate drive belt tensioner as described under the removal procedure and install drive belt over drive belt tensioner pulley. Make sure that all V-grooves make proper contact with pulleys. Make sure spring keeper releases or improper belt tension will occur.


    Pulley, Routing—Accessory Drive Belt 3.0L (2V)/3.0L (2V) FF Engine


    q3244d.gif


    Item Part Number Description 1 10300 Generator 2 6C348 Idler Pulley 3 3A674 Power Steering Pump 4 19703 A/C Compressor 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 8501 Water Pump 8 8620 Drive Belt

    Pulley, Routing—Accessory Drive Belt 3.0L (4V)


    q3735a.gif


    Item Part Number Description 1 3A674 Power Steering Pump 2 8501 Water Pump 3 19703 A/C Compressor 4 8620 Drive Belt 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 10300 Generator
3.4L SHO Engine
Removal
  1. Remove the right front wheel and tire assembly. For additional information, refer to Section 04-04.
  1. Remove the inner fender splash shield.
  1. Remove the alternator shield.
  1. ani_caut.gif WARNING: USE CAUTION WHEN REMOVING OR INSTALLING DRIVE BELT TO MAKE SURE WRENCH DOES NOT SLIP FROMDRIVE BELT TENSIONER OR POSSIBLE PERSONAL INJURY AND/OR DAMAGE TO DRIVE BELT TENSIONER AND DRIVE BELT MAY OCCUR.
    Using a 3/8 inch ratchet on the lifting lug, rotate drive belt tensioner counterclockwise (upward) and engage spring keeper. Remove drive belt from drive belt tensioner.
  1. Lower vehicle.
  1. Remove drive belt.
Installation
  1. Install drive belt over all pulleys (except drive belt tensioner ).
  1. Raise vehicle on hoist.
  1. Rotate drive belt tensioner , as described under Removal procedure and install drive belt over drive belt tensioner pulley. Make sure all V-grooves make proper contact with pulleys. Make sure the spring keeper is released or improper belt tension will occur.
  1. Install the alternator shield.
  1. Install the inner fender splash shield.
  1. Install the wheel and tire assembly. For additional information, refer to Section 04-04.


    Pulley Routing—Accessory Drive Belt, 3.4L SHO


    q3736a.gif


    Item Part Number Description 1 3A733 Power Steering Pump Pulley 2 6B217 (RH) Idler Pulley 3 19703 A/C Compressor 4 8620 Drive Belt 5 6312 Crankshaft Pulley 6 6B209 Drive Belt Tensioner 7 10346 Generator 8 6B217 (LH) Idler Pulley 9 6B217 (Center) Idler Pulley
Drive Belt, Water Pump
Removal
  1. NOTE: If removal of the water pump drive pulley is required, refer to Section 03-03.

    Rotate drive belt tensioner clockwise by hand and remove drive belt from drive belt tensioner .
  1. Remove drive belt from water pump drive pulley and water pump pulley.
Installation
  1. Position drive belt onto water pump drive pulley and water pump pulley.
  1. Rotate drive belt tensioner clockwise by hand and install drive belt over top of drive belt tensioner pulley. Make sure all V-grooves make proper contact with pulleys.


    Pulley Routing—Water Pump Drive Belt


    q3737a.gif


    Item Part Number Description 1 6B209 Drive Belt Tensioner 2 6A312 Crankshaft Pulley 3 8501 Water Pump 4 8620 Drive Belt
Read full answer
Jun 01, 2009 • 1997 Ford Taurus
Not finding what you are looking for?

View Most Popular

2002 Sportage

  • Cars & Trucks

Related Question

How to install a serpentine belt on a 2001 Volkswagen Passat

  • Volkswagen Cars & Trucks

185 views

Ask a Question

Usually answered in minutes!

Popular Questions

Kia sportage fuel gauge unit not working ?

1999 Kia Sportage

Where is fuel filter located in a kia sportage

2006 Kia Sportage

Cruise control will not 'set' on '05 kia sportage

2005 Kia Sportage

1999 kia sportage timing marks

1999 Kia Sportage

Check engine light is on

2000 Kia Sportage

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Kia Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...