2006 Mitsubishi Outlander Logo

Related Topics:

A
Anonymous Posted on Jun 27, 2012

Diagrama de banda de distribucion de mitsubishi outlander

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 1 Answer
  • Posted on Aug 16, 2012
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Aug 16, 2012
Answers
1
Questions
0
Helped
2295
Points
2

Diagrama de banda de tiempo de outlander 2.4 de mitsubishi

3 Related Answers

Anonymous

  • 710 Answers
  • Posted on May 16, 2009

SOURCE: 2004 mitsubishi outlander cooling fans not operating

TAKE A PEEK UNDER THE HOOD IN THE FUSE PANEL FOR THE FUSE AND RELAY FOR THE COOLING FAN. IF THE FUSE IS BLOWN THEN REPLACE IT. IF YOU SUSPECT THE RELAY TO BE BAD THEN TEST IT BY SWAPPING THE FAN RELAY WITH ANOTHER ONE WITH THE SAME PINS ON THE BOTTOM. MAKE SURE IT IS THE SAME SIZE AS WELL. HOPE THIS HELPS.. PLEASE KEEP ME POSTED. THANKS FOR AN HONEST RATING AND FOR USING FIX-YA. GOOD LUCK

Ad

Anonymous

  • 333 Answers
  • Posted on Sep 10, 2009

SOURCE: mitsubishi outlander cooling fans not operating

There is a Recall to replace your cooling fan module because of this concern.

Open your hood and look at the black box bolted to your radiator fan by the battery. If it does not have a green dot on it, you have not had the replacement fan module installed.

Contact your local dealer with your VIN handy to verify the recall has not been done and to schedule an appointment.

If the recall has been done, verify if you have power coming out of the module to the fans, as the fans do burn out eventually.... but rarely both at once.

Anonymous

  • 412 Answers
  • Posted on Nov 21, 2009

SOURCE: remove rear brake drum 2004 Mitsubishi Outlander

Dear Brake Drum Remover,
I'm gonna tell you how to pull this drum off, ya ready?First off, get the rear of the vehicle up in the air safely, Then pull the rear tires off.After those are off then take a gander at the face of the drums, are there shiny brass looking screws installed on the face of that drum?Ifso remove those counterclockwise, then, take a hammer a shock the face off the drum firmly about three times.Now, go to the opposite side on the face of the drum and do that again, keep on doin that until you can wiggle the drum off by hand...easy as that, any other questions get back to me. I'M HERE TO HELP!!!

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

DIAGRAMA DE LA BANDA DE TIEMPO DEL PT CRUISE

todas la bandas de tiempo tienen la misma funcion. Sincronisar los ejes de la valvulas con el eje de los pistones se llama "timing" para que las valvulas de injeccion y la valvulas de escape abran al tiempo correcto sin eso no hay comprecion y carro no encendera. typicamente hay una marca en las poleas que indica la posicion correcta para alinierlas.
0helpful
2answers

DIAGRAMA DE MAZDA MPV 2003 DISTRIBUCION

He mandado a buscar dos veces las cadenas de tiempo de mpv 2000 2.5L y no caen por qu? quien me puede decir la primera foto son las viejas y la otra el segundo par
3_20_2016_2_29_09_pm.jpg3_20_2016_2_29_10_pm.jpg
0helpful
1answer

Diagrama correa de tiempo outlander 2005

que modelo de motor? aqui esta para 2.4
f0b3e8c8-391e-4840-8fba-9e287ac1fece.gif
9helpful
1answer

COMO PONER TIEMPO DE BANDA DE SATURN 3.0

buenas noche me podria enviar diagrama para un saturn 2001 3.0 para cambiar la banda de sincronizacion de tiempo
21helpful
1answer

Quiero poner a tiempo cadena de distribucion ford escape 2005, seria posible me mostraran un diagrama

cuales son las marcas de la cadena de distribucion de una ford escape 3.0
0helpful
1answer

Haw can change the band of distrubution?

ok sure you speak spanish because we says to timing belt = banda de distribucion. I will write in spanish :)

Lo que tienes que hacer con la banda de distribucion de tu Jetta 1994 es quitar las bandas externas de tu auto, luego de esto lo que tienes que hacer es quitar la polea del cigueñal para lo cual iras a requerir un extractor de poleas, ya que extraigas la polea del cigueñal y quites la tolva que guarda a la banda de distribucion y a los de los arboles de levas entonces gira con el maneral el cigueñal hasta las marcas del tiempo q deben estar marcadas en el motor o monoblock y/o en las tolvas, verifica estas marcas poniendo tu auto en punto muerto superior que es que el piston 1 quede hasta arriba lo puedes ver con un desarmador claro para esto tienes que quitar la bujia de tu auto del piston 1.

bueno ya que tengas esto prosigues a marcar la banda con alguna tinta o corrector tambien marca las poleas de los arboles o arbol y la del cigueñal, quita el tensor y va a salir la banda.

cuenta los dientes entre marca y marca y luego de eso marcalos en la nueva banda de distribucion. con el tensor de banda contraido pones la banda verifica que esten en sus marcas y luego vuelve a tensar la banda con su tensor.

si no sabes cuanto tensar solo verificar que la banda no debe doblar mas de 60 grados maximo 90 grados si gira mas entones esta floja.

ya puesta la banda verifica y dale 2 vueltas al cigueñal con el maneral y dado, si quedan en el mismo lugar las marcas luego de 2 vueltas completas de la polea entonces esta a tiempo si se atora se pone demaciado duro entonces las valvulas estan pegando.

vuelve a poner todo lo que desarmaste y listo!
Not finding what you are looking for?

2,305 views

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...