Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Jun 29, 2012
Be the first to answer

Diagram to replace door blend actuator 97 chev blazer

Answer This Question

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Dec 15, 2008

SOURCE: Blend door

ok first put you front seat down and back raise steering wheel . now lay on you back with you head in the drivers floor board. look up see 2 screws remove them and the panel they hold on . look to left main wire harness needs to be moved to the right , up and behind it is th blend actuator 7/32 socket to remove it then manually turn the white peg , total labor 30 min

Ad

Anonymous

  • 1 Answer
  • Posted on Nov 25, 2009

SOURCE: blend door actuator needs replacing does the

no it doesnt ... check out heatertreaters.net if you have to replace the blend doors .... but the actuator is directly behind the glove box...remove the glove box take out 3 screws and remove actuator and replace.....waa laa

Anonymous

  • 5 Answers
  • Posted on Dec 07, 2009

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Anonymous

  • 1 Answer
  • Posted on Apr 05, 2010

SOURCE: how do I remove the dash to replace blend door

blender door on a 2003 grand marquis blows only hot air the ac works

Anonymous

  • 248 Answers
  • Posted on Apr 16, 2010

SOURCE: What do I have to remove to access blend door actuator

very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Where is the blend door located on a 2004 trail blazer
Does it have manual or automatic climate control ? manual or automatic has two temp blend door actuators - driver side & passenger side . Video's on youtube showing where they are .
2004 GMC Blend Door Actuator Replacement Calibration Comparison
Read full answer
Oct 27, 2018 • Cars & Trucks
1helpful
2answers

Location of blend door actuator on 2000 Chevy S-10
Blazer Jimmy Blend door actuator replacement HVAC
Read full answer
Apr 13, 2018 • Cars & Trucks
0helpful
1answer

97 Ford Grand Marquis heater blend door module clicks blows out cold air no warm air?
The air temperature blend door is jammed and this is causing the blend door motor to "skip". REMOVE THE DASH ASEMBLY AND REPLACE THE BLEND DOOR AND THE ACTUATOR.
Read full answer
Jan 04, 2018 • Ford Cars & Trucks
0helpful
1answer

NEED WIRING DIAGRAM FOR 1996 S10 BLAZER. DASH SPEAKERS WORK, BUT ALL DOOR SPEAKERS HAVE QUIT.
Not practical to add the wiring diagrams to questions at this site (there are a lot of them and are hard to view when posted). Your best bet is to use Alldatadiy.com.
Read full answer
Jul 05, 2017 • Cars & Trucks
0helpful
1answer

How to replace the door blend actuator on 2009 lincoln mks
Right side or left ? Electronic Automatic Temperature Control or manual ? Temperature or mode door ?
 Temperature Blend Door Actuator - LH Removal and Installation
NOTE: It is not required to install the new LH temperature blend door linkage parts included in the LH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
LH temperature blend door actuator and linkage
  1. Remove the 2 lower steering column opening cover bolts.
  1. Detach the lower steering column opening cover.
  1. Disconnect the in-vehicle temperature sensor aspirator hose and electrical connector.
  1. Position the instrument panel wire harness away from the LH temperature blend door actuator.
  1. Remove the 3 LH temperature blend door actuator screws.
  1. Disconnect the LH temperature blend door actuator electrical connector.
  1. Remove the LH temperature blend door actuator.
  1. Manually operate, and inspect the LH temperature blend door linkage for incorrect placement, binding or damage.
Temperature Blend Door Actuator - RH, Dual-Zone EATC Removal and Installation
NOTE: It is not required to install the new RH temperature blend door linkage parts included in the RH temperature blend door actuator service part kit if only the temperature blend door actuator requires replacement and the linkage parts are not broken or binding.
RH temperature blend door actuator and linkage
  1. Disconnect the glove compartment damper from the glove compartment.
  1. Remove the glove compartment.
  1. Remove the RH lower instrument panel insulator.
  1. Remove the RH lower floor console trim panel.
  1. Remove the 3 RH temperature blend door actuator screws.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  1. Remove the RH temperature blend door actuator.
  1. Manually operate, and inspect the RH temperature blend door linkage for incorrect placement, binding or damage.
  2. Mode Door Actuator - Defrost/Panel/Floor Door
  3. Removal and Installation
    NOTE: The defrost/panel/floor mode door actuator can be accessed from below the driver side of the instrument panel.
    NOTE: It is not required to install the new defrost/panel/floor mode door linkage parts included in the defrost/panel/floor mode door actuator service part kit if only the mode door actuator requires replacement and the linkage parts are not broken or binding.
    Mode door actuator and linkage
    1. Remove the 3 defrost/panel/floor mode door actuator screws.
    1. Disconnect the defrost/panel/floor mode door actuator electrical connector.
    1. Remove the defrost/panel/floor mode door actuator.
    1. Manually operate, and inspect the defrost/panel/floor mode door linkage for incorrect placement or damage.
    Mode door actuator linkage only
    1. Remove the mode door linkage.
      1. Depress the tab and remove the panel door lever.
      1. Remove the floor/defrost door intermediate lever screw and floor/defrost door intermediate lever.
      1. Pull straight outward to remove the floor/defrost door lever.
    Mode door actuator and linkage
    1. NOTE: When installing the mode door actuator, make sure that the panel door lever and floor/defrost intermediate lever are correctly aligned with the mode door actuator cam.
      To install, reverse the removal procedure.
Read full answer
Nov 10, 2016 • 2009 Lincoln MKS
0helpful
2answers

Blend door stuck open, buick lesabre custom,can not locate blend door to close it
it is controlled by an electronic actuator. look up blend door actuator on google with your year make and modle and it will show a diagram and location, also a part number if you would like to replace.
Read full answer
Nov 01, 2013 • Cars & Trucks
0helpful
1answer

Blend door actuator
bad vacuum actuator or vacuum leak to the vacuum solenoids that operate the blend doors.
Read full answer
Oct 21, 2013 • 1998 Chevrolet Blazer
0helpful
1answer

Diagram for a blend door actuator for a 2000 s10 blazer
i have replaced actuator motor on blend door and new switch on 2000 S-10 and blend door still does not work . Please help .
Read full answer
Jan 16, 2012 • Cars & Trucks
0helpful
1answer

I need a vacume diahgram fer a 97 chev blazer v 6 4 wheel drive. My ac is blowing out the defrosters and non of the other controls are workin
It sounds like vacuum is not getting to the vent, heat and A/C controls. Find the vacuum can. It may be under the hood on one of the inner fenders. The "one-way" check valve is usually located in the line and close to the can, make sure it works properly. The valve could be the very thing that's causing the problem. Trace the lines back to the vacuum block at the intake manifold or fire-wall, and also back to where the line goes thru the fire-wall. Check the can for leaks or obvious holes. They used to be just a plain metal can, but it could be a plastic ball. Check the lines as you go, for breaks and rub-thru's. Move the controls thru all settings and listen for vent door movement. Worst case is a bad vacuum motor or air flow position selector switch, and/or a faulty Blend Door Actuator. If you have been driving around with the Temperature knob or control set at the same spot for months, move it from fully cold to fully hot several times and wait for the air temperature to change each time. This will help reset the blend door and vacuum control system. Hope this helps... Let me know what you find.
Read full answer
Aug 24, 2011 • 1997 Chevrolet Blazer
7helpful
1answer

I have to replace the ac door actuator motor behind the ash tray
are you sure it is not the temp control on the heater control panel that's bad?
please rate if this solves your issue.

A/C Electronic Blend Door Actuator The A/C electronic blend door actuator is located on the rear of the A/C evaporator housing assembly.
  • Its function is to move the A/C air temperature control door on command from the control assembly.
  • The A/C electronic blend door actuator contains a reversible electric motor and a potentiometer. The potentiometer wiper is connected to the actuator output shaft and moves with the output shaft to indicate the position of the A/C air temperature control door.
  • A 5 volt signal is applied to the ends of the potentiometer. The voltage available at the wiper indicates the position of the potentiometer. The expressed value of the actuator wiper voltage is sent to the control module and is matched with the wiper voltage of the module potentiometer. The printed circuit board then drives the actuator motor in whichever direction is necessary to make the actuator wiper voltage agree with the control module wiper voltage.
A/C Electronic Blend Door Actuator
Removal
  1. Disengage two push pins retaining instrument panel insulator to instrument panel. Disconnect courtesy lamp from instrument panel insulator.
    1. Remove floor console. Refer to Section 01-12 .
    1. Working from under instrument panel, remove two retaining screws and metal cover from A/C evaporator housing.
    1. Remove A/C electronic blend door actuator electrical connector.
    1. Remove three remaining retaining screws from A/C electronic blend door actuator.
    1. Pull the A/C electronic blend door actuator away from the A/C evaporator housing for a distance of approximately 25 mm (1 inch) to disengage it from the A/C air temperature control door.
5728f0a.gif
Read full answer
May 24, 2009 • 1997 Lincoln Continental
Not finding what you are looking for?

View Most Popular

Cars & Trucks

Related Question

Where is the blend door located on a 2004 trail blazer

  • Cars & Trucks

286 views

Ask a Question

Usually answered in minutes!

Popular Questions

Blower does not work on my 2006 Chevy Silverado truck

2006 Chevrolet Silverado

1988 chevy silverado fuse box

Chevrolet Silverado Cars & Trucks

2006 chevy Silverado Electric cooling fans do not come on. Replaced all relays. Checked the fans by hot wiring them to the battery and they function. Other than the PCM what else could it be?

Chevrolet Silverado Cars & Trucks

What is the 40a fuse called stud#1 under the hood?

2000 Chevrolet Silverado

Need the correct torque specs for 2004 silverado 1500 calipers

2004 Chevrolet Silverado

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
Http://www.borla.com/media/installatio...

2005 Chevrolet...

PDF Manual
Http://media.gm.com/division/2004...

2004 Chevrolet...

PDF Manual
Http://php3.eesc.com/htdocs...

2007 Chevrolet...

Loading...