2007 Ford Edge SEL Plus Logo

Related Topics:

A
Anonymous Posted on Jul 30, 2012

2007 ford edge middle carrier bearing - 2007 Ford Edge SEL Plus

4 Related Answers

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Feb 09, 2009

SOURCE: 89 Ford Ranger Carrier bearing

All the bearings for the rear diff are pressed off and on, they can be done at home if u have a high quality bearing puller, but to press them on should be done at the machine shop.

Ad

Anonymous

  • 3533 Answers
  • Posted on Jan 12, 2010

SOURCE: 2007 ford edge, three lights are on: ABS, wrench

it sound like a ABS-sensor is sticking are its bad give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Anonymous

  • 226 Answers
  • Posted on Feb 25, 2010

SOURCE: 2007 Ford Edge: Rear Blinkers/Brake Lights out; Not bulbs or fuse

Sounds like you need bulbs on both rear side lights. Does the blinker flassh really fast?

Anonymous

  • 610 Answers
  • Posted on Dec 22, 2010

SOURCE: Seems the Carrier Bearing is out on my 2008 Ford

that depends upon what coverages were offered at the time of purchase, and if you purchased extended coverage. well worth a call to the dealership. they can tell you about any ford warranty that is still in effect. sometimes dealers can work with customers that have a premature problem. in any event, asking if your covered, or if not, will they give you any help, costs you only a phone call. these are tough times , and even the dealerships are looking foe whatever work they can get.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Both carrier bearings on my 2007 ford edge are shot, what can i do to repair this problem? the auto parts store tells me it's not a serviceable part and said i have to replace the driveshaft

get a second opinion from a reputable transmission shop
bearings are always replaceable .Sometimes it is a costly exercise so check out replacements from the wreckers / junk yards
1helpful
1answer

What can cause knock sensor to get bad on 2007 ford edge

Well the knock sensor does not make any noise. It senses the vibration in the engine if there is a spark knock to let the computer know to slow down the spark timing.
You probably have a weak piston or lifter or rod bearing making the noise.
0helpful
1answer

Seems the Carrier Bearing is out on my 2008 Ford Edge with a little under 55,000 miles is this common & isn't it still under Ford Warranty?

that depends upon what coverages were offered at the time of purchase, and if you purchased extended coverage. well worth a call to the dealership. they can tell you about any ford warranty that is still in effect. sometimes dealers can work with customers that have a premature problem. in any event, asking if your covered, or if not, will they give you any help, costs you only a phone call. these are tough times , and even the dealerships are looking foe whatever work they can get.
3helpful
1answer

2007 Ford Edge: Rear Blinkers/Brake Lights out; Not bulbs or fuse

Sounds like you need bulbs on both rear side lights. Does the blinker flassh really fast?
1helpful
2answers

2005 ford escape 3.0L AWD XLT - DRIVESHAFT CARRIER BEARING BAD - CAN IT BE REPLACED OR MUST I CHANGE THE DRIVESHAFT FRONT AND REAR?

if there is some one in your area that balances driveshafts they can change just the bearing for you
1helpful
1answer

Van rumbles and vibrates

Does this van have a carrier bearing in the center of the driveshaft? If it does this could be your culprit,you can tell if it has a carrier bearing by looking at the drive shaft in the middle it will around the driveshaft and bolted to floor support of the van.
0helpful
1answer

89 Ford Ranger Carrier bearing

All the bearings for the rear diff are pressed off and on, they can be done at home if u have a high quality bearing puller, but to press them on should be done at the machine shop.
Not finding what you are looking for?

512 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...