Could you tell me what the diagnostic code p1000 means
What does it mean p1000 code
Here is the definition for a Ford product.
P1000 FORD Description
The On Board Diagnostic (OBD) monitors are performed during the OBD
Drive Cycle. P1000 is stored in continuous memory if any of the OBD
monitors do not carry out their full diagnostic check.
Possible causes
- The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool
Read more: http://engine-codes.com/p1000_ford.html#ixzz24QWlUOlE
SOURCE: Engine light on Diagnostic code is P0601
it is an internal problem in the pcm....if the car is under 8years old and 80000 miles take it to the dealer for free replacement under a fed emissions standard....if over you will have to pay...it could eventually leave you stranded
SOURCE: CAN YOU TELL ME WHAT THE P1000 CODE MEANS FOR A
P1000 means a drive cycle has not completed, it will only clear itself
after driving the vehicle through certain driving conditions. If you
try to clear the code, it will reappear until you repeat the drive
cycle. I am not too familiar with what AE will show, but if you can
access Mode 6 data or the OBD Drive Cycle(These are two options from
the IDS at Ford), It may help to show what tests have either failed or
not completed. Heres what must be done to clear the P1000:
Note: The IAT PID must be between 10-38°C (50-100° F) during the OBD II
drive cycle to enter into all the OBD II monitors. The FLI PID must be
between 15% and 85% at all times.
Drive in stop-and-go traffic with at lease 4 idle periods (30 seconds
each) while observing the status of the OBD II monitor on the scan
tool. If the exhaust gas recirculation (EGR), heated oxygen sensor
(HO2S), evaporative emission (EVAP), secondary air (AIR) (if
applicable) or catalyst efficiency monitor have not completed, drive on
the highway at a constant speed over 64 km/hr (40 mph) not to exceed
104 km/hr (65 mph) for up to 15 minutes. Heavy accelerations, sudden
decelerations and wide open throttles are not recommended. If the scan
tool sends out a three pulse beep at any time, the OBD II drive cycle
has completed.
If there is only one certain component that hasn't completed its test,
there are individual driving conditions to help those tests pass or
fail if something is wrong.
SOURCE: need to know what a p1000 diagnostic code means for a jaguar s ty
Looks like you have acommunication problem with the computer, it is going in to safe mode. Check all computer connections before you go to jaguar.
I have attached a picture of the error code.
hope this helps
SOURCE: Auto Diagnostic Trouble Code
cORRECT. tHIS CODE DOES DEALs With emmissions. P1400 deals with the EGR valve. In case u are not aware, EGR stands for Exhaust Gas Re-circulation. What really this valve does is that it re-cycles some of the exhaust gases into the cylinder for combustion. The EGR valve might be blocked or has malfunctioned. It is advised that this valve changed or consult with a mechanic who is knowledgeable about this technology. a malfunctioned/dis-abled EGR system will cause the car to fail an emissions test, and may cause the EGR passages in the cylinder head and intake manifold to become blocked with carbon deposits, necessitating extensive engine disassembly for cleaning. So it is advised that u repair this ASAP
SOURCE: Jeep Grand Cherokee Limited P0700 diagnostic problem
P0700 means there is a transmission fault code in the transmission controller. Since the transmission controller doesn't have a light attached, it tells the engine controller to turn the light on using this code. You'll have to access the transmission controller to further diagnose the problem.
3,958 views
Usually answered in minutes!
×