Hi I have an 2000 Chevy Monte Carlo, all the lights above the dash do not work. I cannot find the door sensors, I believe this to be the problem. I do not want to tear the latch assembly out if I do not have to. I have a Haines manual for the car but it says nothing about Door sensors or switches. if I could find the switches (Sensors) I could finish troubleshooting the problem. Thank you for any help you can give. Sincerely Frustrated!
All the lights above the dash do not work ?????? DOME light's ??? No light's come on when you open the door or any door ? Wouldn't think all the door ajar switches bad at one time .
Interior Lamps
The interior lamps consists of two groups, lamps that can not be dimmed and lamps that can be dimmed. This first group consists of lamps that may not be dimmed. This Includes those lamps that may be manually turned on by placing the interior lamp switch to the DOME position, or by opening a door or a compartment:
• Auxiliary dome lamp (SEO, RPO 6C7)
• Dome lamp
• instrument panel (I/P) compartment lamp
• Inside rear view mirror lamps
• I/P courtesy lamps
• Reading lamps
• Rear compartment courtesy lamp
• Sunshade vanity mirror lamps
Battery positive voltage is applied at all times to the DIC/RKE fuse and to the switched side of the BATT RUNDOWN PROTECTION relay in the right I/P junction block. The DIC/RKE fuse supplies battery positive voltage to the coil side of the BATT RUNDOWN PROTECTION relay. When the ignition is turned to the ON position, the body control module (BCM) provides a ground to the Inadvertent relay control circuit. This energizes the BATT RUNDOWN PROTECTION relay and applies battery positive voltage to I/P BRP fuse and to the TRK/ROOF/BRP fuse. Battery positive voltage is applied from the I/P BRP fuse to the I/P courtesy lamps, I/P compartment lamp and to the I/P compartment feed circuit to the BCM. Battery positive voltage is also applied from the TRK/ROOF/BRP fuse to the:
If the BCM receives a door lock or unlock input signal, the BCM will activate the BATT RUNDOWN PROTECTION relay, which provides battery positive voltage to all interior courtesy lamps. When any door is opened, the door jam switch contacts close and the BCM receives a door-open input signal. The BCM then applies a ground to the theater dimming ground control circuit illuminating the courtesy and dome lamps.
After all the doors are closed, the courtesy lamps remain illuminated for approximately 40 seconds. The courtesy lamps will also turn on and remain illuminated for approximately 15 seconds after the ignition key is removed, prior to any door being opened.
When the headlamp switch is placed in the DOME position, the BCM receives a ground signal. The BCM then applies a ground to the theater dimming ground control circuit. This illuminates the dome and roof rail lamps.
The courtesy lamps will normally turn off using the theater dimming feature. The BCM provides a pulse width modulated ground to all courtesy/reading, dome, and inside rear view mirror lamps for the theater dimming feature. The BCM will immediately turn off the courtesy lamps if a door lock command is received with all the doors closed, or if the ignition switch is turned to either the ON or RUN position.
The BCM activates the interior lighting output 15 seconds after receiving the class 2 message "Airbags Deployed" from the sensing and diagnostic module (SDM). The interior lamps remain activated for 25 minutes.
The door ajar switch is part of the lock actuator inside the door !
SOURCE: i need a diagram for my 1980 chevy monte carlo
'80 Monte Carlo, a good ride. A Chilton's book is a good investment. It will show you wiring and vacuum hoses and how to do the brakes, etc.
SOURCE: belt diagram for a 2006 chevy monte carlo
There should be a decal on the bottom side of your hood, or somewhere in the engine compartment. If there isn't just put it on the crankshaft (bottom pulley) and go ribs to ribs, and flats to flats, and work your way around.
SOURCE: 2002 chevy monte carlo won't start
this vehicle is equipped with a factory anti theft system if when you try to start the engine and the anti theft light is on then the starter won't start even if your check engine light is not on you would have to scan the body module to pin point the problem to see if it's the anti theft system or the starter, go to a auto parts store like auto zone or pep boys or western auto these store offer free scanning to there customers. if this information has been helpful please let use know good luck
SOURCE: 2000 monte carlo blower switch works on only #5
Not the board. It's you blower motor resistor. It melted.
154 views
Usually answered in minutes!
×