P1860 Code on 1998 Chevy S10

i hooked up my code reader , and got j 1850 vpw and 1850 pmw also says spark ?????? P1850 ??? What's with the J - got j 1850 ??? 4X4 or 2WD ? There is no DTC P1850 for your vehicle . An watch when googling codes not always correct . Closest code is a trans code DTC P1860 (2.2 L) DTC P1860 (4.3 L)
Circuit Description
The torque converter clutch pulse width modulation (TCC PWM) solenoid valve controls the fluid acting on the converter clutch valve. The converter clutch valve controls the TCC application and release. The solenoid attaches to the control valve body within the transmission. The solenoid receives ignition voltage through the OFF/ON/START voltage circuit. The powertrain control module (PCM) controls the solenoid by providing a ground path on the TCC PWM solenoid valve control circuit. Current flows through the solenoid coil according to the duty cycle, percentage of ON and OFF time. The TCC PWM solenoid valve provides a smooth engagement of the TCC by operating during a duty cycle percent of ON time.
When the PCM detects a continuous open, short to ground or short to power in the TCC PWM solenoid valve circuit, then DTC P1860 sets. DTC P1860 is a type B DTC.

The vehicle cranks but won't start an run ???? Does it have spark ? Pull a plug wire off a spark plug an hold near engine ground , does it spark ? Does it have fuel pressure ?

https://www.youtube.com/watch?v=SUxagOAVS5M&t=386s

P1860 All GM - TCC (transmission Torque Converter Clutch) PWM Solenoid Circuit Electrical.
P1860 Description The Torque Converter Clutch Pulse Width Modulation (TCC PWM) solenoid valve controls the fluid acting on the converter clutch valve. The converter clutch valve controls the TCC application and release. The solenoid attaches to the control valve body within the transmission. The solenoid receives ignition voltage through circuit 239. The Powertrain Control Module (PCM) controls the solenoid by providing a ground path on circuit 418. Current flows through the solenoid coil according to the duty cycle (percentage of ON and OFF time). The TCC PWM solenoid valve provides a smooth engagement of the torque converter clutch by operating during a duty cycle percent of ON time.
When is the code detected? When the PCM detects a continuous open, short to ground or short to power in the TCC PWM solenoid valve circuit, then DTC P1860 sets. DTC P1860 is a type B DTC.

Possible causes - Faulty Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid
- Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid harness is open or shorted
- Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid circuit poor electrical connection. Unless you have a factory manual and very good auto repair skills this is best left to an expert. It is a messy dirty job that requires removing the parts inside the transmission for testing..

TCC is the Torque Converter Clutch solenoid. This is in the transmission.

Replace the TCC solenoid in the transmission !
Ignition voltage is provided to the torque converter clutch pulse width modulation (TCC PWM) solenoid valve. The PCM controls the solenoid with a negative duty cycle in order to control application and release of the TCC. When the solenoid is commanded OFF, the PCM senses high voltage.When the solenoid is commanded ON, the PCM senses low voltage.
DTC P1860 sets if the PCM detects a voltage that is outside of the calibration limits. DTC P1860 is a type B DTC .
Do you know what the TCC is ?

Possible causes
- Faulty Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid
- Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid harness is open or shorted
- Torque Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid circuit poor electrical connection

CODE P1860 TORQUE CONVERTER CLUTCH PWM SOLENOID CIRCUIT MALFUNCTION. THE TCC PWM SOLENOID FAILED.

P1860 TCC PWM Solenoid Circuit Electrical (GM)
this is a code saying the overdrive lock up soleniod
is not working properly

code - po1860 tcc pwm solenoid circuit malfunction 4t80- E conditions.5 possible causes 1. tcc solenoid control circuit is open or shorted to ground. 2.tcc solenoid control circuit is shorted to system power b+. 3.tcc solenoid power circuit is open check the trans fuse. 4.tcc solenoid is damaged or has failed. 5.pcm has failed.

DTC P1860 is a type "A" DTC and indicates a torque converter clutch pulse width modulation solenoid electrical problem. When set it disables shift adapts and inhibits TCC functions such as the lock/unlock when in 4th-OD. Possible flaky TCC-PWM solenoid.
If you have a 4T65E the TCC-PWM solenoid is located under the side cover assembly. Not exactly easy to replace DIY. Engine/tranny has to be dropped down on the sub-frame assembly.

You could check the input voltage (12 volts) and ground/low to the solenoid via the main electrical connector. And check the resistance of the solenoid at the respective pins on the above connector. Not sure what the value is but you can get that from a transmission service shop or the dealer's manuel.

Assuming you have the 4T65E auto transaxle the 20 way electrical connector is located driver's side top. You should see it looking in. Gray connector and the only electrical plug going to the transmission. Twist counterclockwise. 

Other than checking the wire harness, and just an example once the solenoid is proven bad and replaced the local AAMCO charges around $500-$600 including the part but cost will vary depending on where you live. Good luck and sorry for the bad news. Keep me posted, be glad to help.

Replace your tps it tells the trans when to shift hope this helps you