Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

Head bolt pattern 4.0 - Jeep Cherokee Forum

https://www.cherokeeforum.com > head-bolt-pattern-4-...
Apr 12, 2017 - step 4...tighten all bolts except #11 to 110ft/lbs, then tighten #11 to 100ft/lbs... JeepingDan's Avatar.
Torque specs. for 4.0 cylinder head 2002 - Jeep Cherokee ...
Jun 23, 2017
cylinder head torque specs on 94 4.0 - Jeep Cherokee Forum
Sept 2, 2015
4.0 torque specs - Jeep Cherokee Forum
Apr 12, 2017
Cylinder Head Bolts & Torque - Jeep Cherokee Forum
Oct 1, 2019
More results from www.cherokeeforum.com

Videos as well.

https://www.google.com/search?q=torque+sequence+of+the+head+bolts+on+a+1999+Jeep+Cherokee+4.0

..

Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

http://olybrake.com/pdf/fel_pro_torque_specs_guide.pdf

Check here

specs, rear?
we just set them to 35ft./lbs
if frisky you can read the fSM for that.
or use google, ever use google,.????? amazing my 1st hit
here ill type it for you....... omg

http://www.jeepforum.com/forum/f67/rear-shock-bolt-torque-954751/#post9025080

Click here to see.

Go to autozone.com create a free account put in you cars model year etc... then look at the free manual for replacing head gasket it will have a bolt tightening sequence diagram. also they usually have to be taken off in a paticular sequemnce to avoid warping the head. If aluminum heads they usually recommend new head bolt set and having the head shaved (Leveled)

i'm guessing this is a V6 3400 since the headline is a 2000 Grand Am GT
44 LB FT plus 95 degrees

main caps 80 ft. lbs.

Assuming the motor is an inline six
1.Middle bolt is number 1.Clockwise torque to 22 f/lb
2.Same pattern to 45 f/lb
3. same pattern to 100 f/lb
Be sure to use loctite 592 to the threads and some head gasket sealer to both sides of the head gasket.
Hope this helps

Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

1. Disconnect the negative battery cable.
2. Drain the cooling system.
3. Disconnect the hoses at the thermostat housing.
4. Properly relieve the fuel system pressure.
5. Remove the cylinder head cover.
6. Loosen the rocker arms.
7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.

1. Remove the intake and exhaust manifold from the cylinder head.
2. Disconnect the spark plug wires and remove the spark plugs.
3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
4. Remove the accessory drive belt(s).
5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
6. Remove the intake and exhaust manifold assembly.
7. If equipped with A/C, perform the following:
   1. Remove the compressor and position it aside with the lines attached.
   2. Remove the compressor bracket bolts from the cylinder head.
   3. Loosen the through bolt at the bottom of the bracket.
   
   
8. Remove the alternator.
9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.

1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:

1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.