Question about 2000 Mitsubishi Lancer

1 Answer

Guages not working,

All voltages and earths chack out ok, circuit board is fine as well.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 5,370 Answers

If all voltages checked ok,then most probably its faulty instrument cluster board on which gauges are connected.Yes if cluster circuit board looks ok,then also it can be faulty.Somewhere there is minute short or burn on board then such prolem arises.
Also check the fuse box.One under hood and other under dash.Inspect each and every fuse and see if all are fine or not.
---------------For more troubleshooting on these cluster gauges i suggest you to refer the list of help links mentioned below.Its step by step instructions will help you to confirm the exact cause of problem in these conditions:---------
Click the link below:------

2004 Toyota Tundra: Oil Gauge and Temp Gauge Not Working?

http://howtobyme.blogspot.in/2012/05/2004-toyota-tundra-oil-gauge-and-temp.html

--------------

2005 Lexus SC430: Fuel Door, Dome light and Fuel Gauge Fuse Location?

http://howtobyme.blogspot.in/2012/05/2005-lexus-sc430-fuel-door-will-not.html
----------

Toyota 4Runner: Temperature Gauge Sensor

http://technoanswers.blogspot.in/2012/04/toyota-4runner-temperature-gauge-sensor.html
------------

Temperature gauge sits over half way mark?

http://schematicsdiagram.blogspot.in/2012/04/temperature-gauge-sits-over-half-way.html

---------------

Heater blows intermittently and temp gauge goes erratic?

http://technoanswers.blogspot.com/2012/01/heater-blows-intermittently-and-temp.html

----------

Temperature gauge does not move and no heat when heater is ON?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-does-not-move-and-no.html

-----------

2003 Pontiac Grand Prix: Erratic Fuel Gauge?

http://technoanswers.blogspot.in/2012/06/2003-pontiac-grand-prix-erratic-fuel.html


-----------

Temperature gauge keeps fluctuating up and down close to red?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-keeps-fluctuating-up.html


-------------

Temperature gauge on the dash quit working on Pontiac Grand Prix?

http://technoanswers.blogspot.com/2012/01/temperature-gauge-on-dash-quit-working.html

---------------

Fuel gauge jumps from empty to full?

http://schematicsdiagram.blogspot.com/2011/12/fuel-gauge-jumps-from-empty-to-full.html

--------------

Gas gauge stuck on empty on 2002 Mercedes Benz 240c?

http://repairhelpcenter.blogspot.in/2012/02/gas-gauge-stuck-on-empty-on-2002.html
---------------

Oldsmobile Temperature Gauge Lamp Switch?

-----------------


Fuel gauge drops to Empty?

http://technoanswers.blogspot.com/2012/01/fuel-gauge-drops-to-empty.html

----------------

Dodge neon gauges not working?

http://technoanswers.blogspot.in/2012/02/dodge-neon-gauges-not-working.html

------------


Temperature gauge went up?

http://schematicsdiagram.blogspot.com/2011/12/temperature-gauge-went-up.html

------------

Temperature gauge stays At cold on jaguar?

http://technoanswers.blogspot.in/2012/02/temperature-gauge-stays-at-cold-on.html
-----------


How to replace Instrument panel and dashboard on Toyota car?

http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-instrument-panel-and.html

-----------

How to remove instrument panel on Chevrolet car?

http://technoanswers.blogspot.in/2012/02/how-to-remove-instrument-panel-on.html

-----------

How to remove control panel on Buick regal?

http://howtobyme.blogspot.in/2012/02/how-to-remove-control-panel-on-buick.html
---------------
These details will help.Thanks.

Posted on Nov 28, 2012

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 03 GMC 3500 dually that the driver's side fender running lights won't light up. The passenger side work fine. Also my reverse light doesn't light up either. Could that be the problem?


check battery voltage both sides of stop light switch if if none check fuse , if one side only replace switch, if ok check voltage at light bulb holder if ok check bulb or earth system

May 02, 2017 | GMC Sierra 3500 Cars & Trucks

2 Answers

2007 silverado 1500 brake lights dont work, bulbs are fine, power from the brake switch wire blue /white trace illuminates when the pedal is depressed


Check the bulb ground connection. Power may be reaching the bulbs but you need a ground to complete the circuit.

Apr 04, 2017 | Cars & Trucks

1 Answer

Power seat, mirrors, inside lights don't work.


If fuses ok, check for voltage with a meter at one of the interior lights, if no reading, earth elsewhere and if then it does read a voltage, you've got a bad earth common to those 3 circuits. That's how I'd begin if the fuses and relays were ok and powered.

Sep 05, 2012 | Cars & Trucks

2 Answers

Car seems to be charging ok but some thing


Check for consumers staying on such as interior lights , radio etc.. To check for current draw, you need an AMP meter. remove the negative battery terminal. Connect one amp meter lead to the battery negative terminal and the other to the earth cable. Hold the cable against the battery negative cable, close all doors and press bonnet switch to closed position. Activate the alarm and wait for it to arm. Once it has armed itself, separate the earth cable from the battery terminal keeping the amp meter connected. read the current draw. Should be less then 100 milli amps. Usually +- 40ma. To check which circuit has current draw remove one fuse at a time and check if current draw drops. A drop in current draw will indicate that the problem is on that fuses circuit. Also check alternator charge rate. To check this hold a volt meter across the battery terminals. with engine off, should get battery voltage. Start the vehicle, battery voltage should rise to 13 -14v and maintain this voltage with the headlights on. The battery itself could be faulty, you would need to do a load test on the battery. Load tester needed to do this.

Apr 24, 2010 | 1996 Audi A6

1 Answer

My brake lights do not work everything else does replace flasher unit and brake light switch checked all fuses and wiring all seem good on a 97 eclipse


If lights don't work, they either have no power, or no return earth. Therefore, remove a stoplamp globe and measure the voltage present in the globe socket. Next with a mutimeter, or battery powered light circuit, check that the globe sockets are in fact earthed to the frame.. If the earth is ok, and there is no power present, then you have a break in the wiring between the stoplamp switch and the rear of the vehicle.

Mar 18, 2010 | 1999 Mitsubishi Eclipse

2 Answers

Cooling fans on radiator will not run. Voltage in plug at block thermostat is 5.4.this therm provides an earth switch. Bypassed the thermo to earth and fan relay engages momentarily only. Relay is ok....


The fan control thermo switch should be either "off" or "on".
Voltage should measure either +12 or 0V, depending on coolant temperature.
Replacing it should fix your problem.

Jun 20, 2009 | 2000 Daewoo Nubira

1 Answer

Lighter won't work on mini cooper S


check to see what circuit you have missing frst ie the earth to the sigarette light or the power feed

The outside of the holder will be earth and if all the fuses are ok it still will not work if the earth has gone

hope this helps

svs
07923 479640

Jun 13, 2009 | 2007 Mini Cooper S Convertible

1 Answer

2001 Daewoo Lanos Fault 63.58X 'B'


DTC 63 Will Set When
No voltage is supplied by the ECM through the EST “B” line while reference pulses are received by the ECM from the crankshaft position sensor
check white wire terminal B on ignition coil to ECM terminal C14 for open circuit or short to ground while disconnected if thats ok check for voltage signal at B while cranking no signal ECU faulty. voltage signal also on A terminal while cranking and check earth terminal C to body no higher than 5 Ohms
power is terminal D 12V
if getting power, earths good, and both signal voltages are going into coil pack, coil pack is faulty.

May 30, 2009 | 2001 Daewoo Lanos

Not finding what you are looking for?
2000 Mitsubishi Lancer Logo

1,999 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...