Remove steering wheel on 2004 oldsmobile alero

SOURCE: 1992 Oldsmobile cutlass sierra

First you need to go to the local parts store and get a steering wheel puller and a clock spring compressor tool. You can rent them but just cheaper to buy it and return it. I got mind like 35 bucks together.
You will remove the horn button just by pulling it towards you be careful not to rip the horn wire out. Next there may be a retainer clip remove it with a pair of needle nose pliers. Next get a breaker bar or a impact gun to back the center nut off. Once off use the steering wheel puller by inserting the threaded bolts into the threaded holes directly beside the center pin. ease the puller onto the center pin and tighten down until the steering wheel starts to move back towards you continue until off. On some trucks there is a steel plate covering the housing to the left side and towards the top are two small torx screws remove them and remove the cover. Next grab your clock spring compressor and install it similar to the way you did the wheel puller you will tighten down the center bolt slightly decompressing the clock spring. as you compress the clock spring look to the center there is a small retainer clip that looks like it is made into the center pin pry the clip off making sure not to damage it and remove the compressor tool, remove the clock spring making sure to pay attention on how it comes apart you can put it all back together. Remove the turn signal switch should be 3 phillips head screws. You may need to disconnect the horn wire at this point it just turns slightly and pulls out. After you remove the clock spring you will see the lock cylinder body, follow the body towards the center pin. There will be a small torx bit or a phillips screw to it will be silver and very shinny at the end of the lock housing remove it and slide the lock cylinder out. Install the new one and reverse the steps.
hope this helps...........good luck!

SOURCE: steering wheel is hard to turn in my 2004 oldsmobile alero.

Power steering pump has gone out. You will need to replace your power steering.

SOURCE: need to know if i

here are step by step instructions on the removal and installation of your fuel tank and fuel pump. please do not forget to rate and comment about your experience with fixya today.
Removal & Installation

1. Before servicing the vehicle, refer to the precautions section.
   
2. Relieve the fuel system pressure.
   
3. Drain the fuel tank.
   
4. Remove or disconnect the following:
   
5. While holding the modular fuel sender assembly down, remove the snapring, if equipped or if equipped with a cam lock ring use Fuel Sender Lock Nut Tool J-39765 to press down and rotate the cam lock ring to remove it.
   
   WARNING If the modular fuel sender assembly is retained by a snapring, it may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
   
   • Fuel sender assembly
     
   • External fuel strainer
     
   • Connector retainer from the wiring harness and the fuel pump
     
6. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tab in the same manner.
   
7. Remove or disconnect the following:
   
   • Fuel pump electrical connection by lifting the cover assembly
     
   • Baffle and pump assembly from the retainer by rotating the fuel pump baffle counterclockwise
     
   • Fuel pump outlet by sliding it out of slot
     
   • Fuel pump outlet seal
     

1. • Fuel pump outlet with a new seal by sliding it in the reservoir cover slots
     
   • Fuel pump and baffle assembly onto the reservoir retainer by rotating it clockwise until seated
     
   • Lower retainer assembly partially into the reservoir by aligning all 3 sleeve tabs and pressing the retainer onto the reservoir making sure all 3 tabs are firmly seated
     
   
   NOTE Gently pull on the fuel pump reservoir to assure it is secure. If not secure, replace the entire fuel sender.
   
   • Connector retainer to the wiring harness and the fuel pump
     
   • External fuel strainer
     
   • Snapring, if equipped to the retainer slots while holding the modular fuel sender assembly down or use Fuel Sender Lock Nut Tool J-39765 in order to install the cam lock ring
     
   • Fuel tank
     
   • Negative battery cable
     
2. Pressurize the fuel system and verify no leaks.
   

SOURCE: cannot unlock the steering wheel on oldsmobile intrigue 2001

is it the right key for that car? cause if not then that is the problem... if it is the right key, then you might have to replace the key cylinder cause you may have something broken in it...

SOURCE: How do you remove the interior door panel of a 4

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.