B1596
ABS Module
Service Continuous Codes
NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index
DTCs
DTC Caused By
Description
Action
B1342
ABS Module
ECU is Defective
INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section.
B1484
ABS Module
Brake Pedal Input Open Circuit
Go To Pinpoint Test D .
B1596
ABS Module
Service Continuous Codes
NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
B1676
ABS Module
Battery Voltage Out of Range
Go To Pinpoint Test E .
C1145
ABS Module
Speed Wheel Sensor RF Input Circuit Failure
Go To Pinpoint Test B .
C1155
ABS Module
Speed Wheel Sensor LF Input Circuit Failure
Go To Pinpoint Test B .
C1165
ABS Module
Speed Wheel Sensor RR Input Circuit Failure
Go To Pinpoint Test B .
C1175
ABS Module
Speed Wheel Sensor LR Input Circuit Failure
Go To Pinpoint Test B .
C1222
ABS Module
Speed Wheel Mismatch
Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test.
C1266
ABS Module
ABS Valve Power Relay Circuit Failure
Go To Pinpoint Test K .
C1296
ABS Module
Wheel Speed LF Signal Fault
Go To Pinpoint Test C .
C1297
ABS Module
Wheel Speed RF Signal Fault
Go To Pinpoint Test C .
C1298
ABS Module
Wheel Speed RR Signal Fault
Go To Pinpoint Test C .
C1299
ABS Module
Wheel Speed LR Signal Fault
Go To Pinpoint Test C .
C1300
ABS Module
ABS Hydraulic Pump Motor Circuit Failure
Go To Pinpoint Test A .
C1805
ABS Module
Mismatched PCM and ABS Modules Do Not Match
CHECK the part numbers. INSTALL the correct module.
C2775
ABS Module
TC ON/OFF Switch Stuck Failure
Go To Pinpoint Test H .
U0073
CAN Bus
Control Module Communication Bus Off
REFER to Section 418-00 .
U1900
CAN Bus
CAN communication Bus Fault - Receive error
REFER to Section 418-00 .
U2023
CAN Bus
Fault received from External Node
REFER to Section 418-00 .
SOURCE: 2003 ford crown vic hard steering
i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras
SOURCE: i need a diagram for a 1998 ford crown vic interior fuse box
ITS FUSE #16 AND ITS a 20A FUSE
SOURCE: Replace horn on 2006 crown vic
I believe once you have mounted the horn and connected the wire you will find that the horn wire was cut at (by) the steering coloum that the siren override was hooked to,you will have reconnect this,I hope this helps you
SOURCE: 1999 FORD CROWN VIC. 4.6 - PROBLEM, NOISE
This is caused by the IAC valve. Over time the valve becomes gummy and inoperative. Get it replaced and the problem is solved. IAC stands for idle air control, hence the stalling concern.
6,129 views
Usually answered in minutes!
×