Routing diagram serpentine belt 1991 olsmobile cutlass supreme 3.1 liters

go to: https://www.google.com/search?newwindow=1&safe=active&tbm=isch&q=v+belt+routing+diagrams+for+1988+cutlass+supreme&chips=q:v+belt+routing+diagrams+for+1988+cutlass+supreme,online_chips:oldsmobile+cutlass&sa=X&ved=0ahUKEwjswpCRzaLXAhVL5CYKHYzHAIUQ4lYILCgF&biw=1267&bih=620&dpr=1.25

Search Results

images for diagram on how to replace a serpentine
How To Install Replace Serpentine Belt Oldsmobile Alero 99 ...? 3:33https://www.youtube.com/watch?v=jkzXTt43uwwFeb 9, 2012 - Uploaded by 1A Auto PartsHow To Install Replace Serpentine Belt Oldsmobile Alero 99-04 2.4L .... There should be a belt routing diagram on the frame rail or under side ...serpentine belt install 3.1/ 3.4 v6 - YouTube? 4:00https://www.youtube.com/watch?v=GYoWuvEZ2DcMay 6, 2013 - Uploaded by JoeTheAutoGuythis a serpentine belt install video on a 3.1 liter gm v6 , 3.4 liters are the same in ... Replacing the alternator or serpentine on anyOldsmobile Alero 99-04 3.4 Liter ... Serpentine Belt Replacement 1995-2005 Chevrolet Cavalier .

http://www.2carpros.com/diagrams/plymouth/voyager/1991 Here are the diagrams.

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

my manual says it's in or under the glove box...

2.8L and 3.1L Air Pump Belt

1. Disconnect the negative battery cable.
2. Loosen the air pump.
3. Remove the worn belt.

To install:

1. Adjust the belt to specifications and tighten the pump mounting bolts.
2. Connect the negative battery cable.

2.3L Power Steering Belt

1. Disconnect the negative battery cable.
2. Loosen the adjustment bolts.
3. Remove the power steering belt from the pulley.

To install:

1. Route the belt around the pulley.
2. Adjust the belt to specifications, then tighten the adjustment bolts.
3. Connect the negative battery cable.

See Figures 6 through 15

Fig. Fig. 6: Unfasten the retaining bolts...

Fig. Fig. 7: ... then remove the serpentine belt guard

Fig. Fig. 8: ...

Fig. Fig. 9: ... then remove the serpentine belt

1. Remove the belt. Clean the accessory drive belt surfaces.

Fig. Fig. 10: Serpentine drive belt routing-2.2L engine

Fig. Fig. 11: Removal and installation of the serpentine belt-2.3L engine

Fig. Fig. 12: Serpentine belt routing-2.5L engine with and without A/C

Fig. Fig. 13: Use an 18mm box end wrench on the pulley nut to rotate the tensioner on the 3.8L engine

Fig. Fig. 14: in. breaker bar to rotate the tensioner

Fig. Fig. 15: On the 3.4L, use a box end wrench, then rotate the tensioner clockwise and remove the serpentine belt

Remove the belt guard or coolant recovery reservoir as required.

Diagram? just v belts. It should have 4...... ALT PS A/C and Air Pump.

Here's a link to a series of videos that will explain how to change the serpentine belt.

http://www.wonderhowto.com/how-to/video/how-to-change-a-serpentine-belt-on-your-car-39904/

Here is a diagram of the belt routing which will help you put the belt back on correctly...

Have you checked under the hood, should be a belt diagram some were around the fan shroud .

If the belt you are talking about was in the condition you say it is, it is not the timing belt but the serpentine drivebelt. It is not difficult to replace and should be done asap before you run into a major problem. As far as I remember you have a timing chain inside your engine.,When replacing it, make a routing diagram or find the sticker that shows this before removing the old belt.Have someone at the parts store show you the tensioner and how to depress it to r&r the belt.