Finding Interior trim parts for 98 Expedition

Of course the dealer can probably supply the mouldings. Most large cities have companies that supply body shops with aftermarket parts which include things like trim.
You can check with a local body shop or the phone book for suppliers, as well as online.

Expedition Trim Panel Removal

NOTE The door glass must be completely raised.

1. Remove the window control switch plate.
2. Remove the door handle bezel.
   WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   
3. Remove the two bolts and three screws, and remove the door trim panel.
4. Remove the finish cover to access the two center screws.
5. Disconnect the electrical connectors.
   
   
   
   

   Fig. Expedition - Trim Panel Screws shown
   

6. Remove the door handle bezel.
7. Use service notch.
   WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
   
8. Remove the two bolts and three screws, and remove the door trim panel.
9. Disconnect the electrical connectors.
   
   
   

   Fig. Navigator - Trim Panel Screws shown
   

10. Position the water shield aside.
11. If equipped, disconnect the lock cylinder rod.
12. Disconnect the exterior door handle actuating rod.
13. Remove the bolts and position the front door latch aside.
14. Disconnect the electrical connectors.
15. Release the interior door handle cable and remove the front door latch.
16. Position the cable cover aside.
17. Release the conduit and the interior door handle cable.
18. Release the locking tab and remove the front door lock actuator.
19. To install, reverse the removal procedure and note the following:
    1. Tighten the door latch screws to 80 inch. lbs. (9 Nm).

This procedure is followed to check and fix door locks.

Hope helps.

You won't be putting it back on it's track. You will be replacing a broken regulator cable most likely.

You remove any screws you find around the arm rest and door handle,then carefully pry the trim away from the door structure.

You will break a few christmas tree fastners along the way. You get them at an auto paint and body supply house

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Very easy to do...I have a 1990 and they are interchangeable....88-94: Door Panel

1. Fully lower the door glass.
   
2. Remove the arm rest, door lock knob and inside door handle escutcheon.
   
3. For vehicles with manual windows, remove the regulator handle which is retained by a spring clip.
   
4. Gently pry the door panel away from the door.
   

Interior side and floor trim removal procedures-Pathfinder


Remove the lock button first before removing the door panel


Remove the plug to gain access to door panel retaining screws


Remove the trim cover


Remove the door handle trim


Remove the power window switch trim panel


After loosening the power window switch trim panel, disengage the electrical connection


Remove all the necessary trim panels before removing the door panel clips


View of the door panel retaining clip-clip must be installed in the hole straight


Make sure the watershield plastic is in place before installing the door panel

Installation is the reverse of removal.

check for binding by interior door slide if looks good remove trim ring around interior handle and on plastic lock slide use a dry lube or graphite if still not releasing remove panel --2 screws in arm rest/door grab than carefully pull straight back starting at bottom corner might need a screw driver to release the plastic clips on panel if u have help once panel is off they can hold panel away or you can push out switch panel and remove door panel out of the way check the lock rod plastic clips for damage and or binding repair or replace problem replace panel -good luck

please rate if this helps. Section 01-05: Trim, Interior 1995 Thunderbird, Cougar Workshop Manual REMOVAL AND INSTALLATION The interior trim component Removal and Installation procedures generally apply to all models. If some of the steps do not apply to the particular models being serviced, proceed to the next step. Trim Panels, Door Removal and Installation

1. CAUTION: Do not pry front door trim panel (23942). Prying on front door trim panel will break the hook retainers.
   Disconnect battery ground cable (14301) .
   

1. Carefully pull front door trim panel finish panel (23712) away from front door trim panel .
   
   
   
   
   

Item Part Number Description 1 23713 Front Door Trim Panel Finish Panel 2 17B676 Outside Rear View Mirror Control 3 14028 Door Lock Switch 4 55928-S55 Screw (5 Req'd) 5 14529 Window Regulator Control Switch 6 23942 Front Door Trim Panel

1. Disconnect wires from front door lock switches (14017), outside rear view mirror controls (17B676) and window regulator control switches (14529) , if equipped; remove front door trim panel finish panel.

1. Remove front door trim panel retaining screw through front door trim panel finish panel opening.
   
   Trim Panels, Door
   
   
   
   
   
   Item Part Number Description 1 20124 Front Door 2 23942 Front Door Trim Panel 3 383356-S100 Nut (2 Req'd Each Side) 4 56903-S58 Screw (2 Req'd Each Side)

1. Remove interior lamp lens cover.

1. Remove screw through interior lamp opening.

1. Slide front door trim panel upward to disengage hooks.

1. Rotate top of front door trim panel away from front door (20125) , and lift bottom hooks from front door.

1. Disconnect window regulator jumper wire (14A630) .

1. Remove front door trim panel.

1. To install, reverse Removal procedure.

Remove or Disconnect

Door handle trim plate.

1. .Install or Connect
   
   
2. Electrical connector and door lock cable.
3. Trim panel by engaging hooks on backside of panel.
4. Push pin fastener in defroster duct.
5. Screw from behind lamp assembly.
6. Courtesy lamp assembly.
7. Two screws in arm rest.
8. Arm rest cover plate.
9. Door handle trim plate.

There May Be A Need to Drill Out RIVETS that Hold Motor in place,. Just Replace with>>MACHINED SCREWS & BOLT'S




Remove or Disconnect

1. Trim panel. See: Doors, Hood and Trunk\Doors
2. Four tabs retaining switch.
3. Electrical connector.

Install or Connect

1. Electrical connector.
2. Snap switch into trim panel.
3. Trim panel.

Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional.
The inside door panel must come off.
1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area.
2. Pry off power window switch panel and remove door panel screw at this area.
3.Remove interior door light cover and remove screw at this area.
4. Remove plastic cover at door handle.
5. The interior door panel can now be lifted up to release it from it's fasteners.
6. Disconnect light and push power window switch assembly through the door panel and it can be set aside.
7. Disconnect mirror power at coupler.
8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely.
9.Thread electrical connection into door panel and install mirror.
10. Smile when mirror works and drink a beer!
rayman

1. Remove the philips screw in the plastic trim by the mirror and remove the trim piece.
2. Using a flat blade screw driver gently pry up the front of the panel holding the window and door lock switches. This pulls the assembly out of the spring clamp. Pull it up and forward to remove it from the arm rest.
3. Remove the two philips screws holding the switches to the trim piece.
4. Find the two screws holding the arm rest. They're at the junction of the arm rest and the switch assembly. Only the one going into the door needs to be removed.
5. Gently pry the trim piece from the door handle. There are two spring clamps, one in the front and one in the rear of this plastic piece.
6. There is a hidden phillips screw that needs to be removed. It's located at the inside bottom rear corner of the door panel. It's hidden in the carpet trim.

After this last screw is removed the door panel can be lifted straight up and off. Feed the cable harness through the hole and your're done.