Cars & Trucks Logo
Posted on Feb 01, 2013
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Changing front axle assembly or wheel hub or both? Either way, need torque specs for all bolts.

Have a hum in right front that gets louder and increases vibration both by about 50% when turning to the right. Used to disappear when driving straight or turning left. Now still aparant when at all times. With four wheel drive activated, hum changes to a louder noise and vibration increases 200%-300%. Obvious oil/grease stain on lower control arm just inside the wheel. CV boots not torn or visibly damaged. Any thoughts?

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Chevrolet Expert 284 Answers
  • Posted on Feb 02, 2013
Anonymous
Chevrolet Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: May 27, 2012
Answers
284
Questions
1
Helped
67697
Points
922

You've got a bad axle shaft in the front and possibly a bad bearing in the hub. 4/wheel drive makes the front axle actually work. Theys no real pressure on these shafts when in 2/wheel drive.

5 Related Answers

jmgldsmth

Jim Goldsmith

  • 2005 Answers
  • Posted on Apr 20, 2009

SOURCE: 2001 Chevrolet Cavalier front End Roar

You must replace wheel bearings in pairs to avoid loading the old bearing and, in time ruining your new bearing hub it is possible that you have already damaged the new hub

Ad

Anonymous

  • 333 Answers
  • Posted on Sep 10, 2009

SOURCE: Replacing front wheel hub assembly on 2006

Caliper mount bolts are 74 ft/lbs
Driveshaft axle nut is 177 ft/lbs
Hub and bearing mounting bolts are 133 ft/lbs

Testimonial: "The info on the torgue specs was very helpful. I couldn't find it anywhere. Thanks a bunch!"

Anonymous

  • 5 Answers
  • Posted on Sep 10, 2009

SOURCE: humming noise from right front tire and front tire

could be ball joint tie rods alignment lift it n check to see if the tire has any play wen u shoake it by grabbin both sides and just a small back n forth movement to see any unusual play. if your not good at this take it to an alignment guy n theyll check the suspension before they do anything

Ray Keckeisen

  • 599 Answers
  • Posted on Dec 09, 2009

SOURCE: 2005 Chevrolet Silverado 1500HD 4 wheel drive

177 ft lbs

Anonymous

  • 714 Answers
  • Posted on Jan 16, 2010

SOURCE: scraping noise from left front wheel area grease

replace your cv joints!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2003 Chevy Silverado 1500 2WD torque specs please

• Axle Shaft nut - 177 ft-lb
• Hub and bearing assembly to steering knuckle bolts - 133 ft-lb

2003 chevy silverado 1500 4.3 v6. Changing steering rack and

https://www.justanswer.com > ... > Chevrolet Repair
Jan 11, 2021 - Below are the torque specs you requested: Steering Rack-to-frame mounting bolts: 136 lb. ft. Outer tie rod nut: 37 lb. ft. Outer tie rod ...
1 answer · 1 vote: Coupler clamp bolt to the intermediate shaft: 33 ft. lb.

People also ask

1helpful
1answer

What is the size socket required for a 2012 Ford Fusion Axle nut? Also, what is the Torque spec to secure it back on? Working with Front-Right wheel.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow
2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...
Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..
2helpful
1answer

2014 Ford Fusion 2.5L, 2WD Torque Specs for front wheel hub assembly needed Axle nut/bolt, Hub bolts

the four axle nuts, 98 ft lbs, tighten in criss-cross pattern.
The hub nut/wheel bearing, 148 ft lbs, use new nut, don't let vehicle weight sit on the ground while torqueing, it could damage the wheel bearing.
If I left something out, give me a holler.
0helpful
1answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually

The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached
0helpful
2answers

Front axle to hub nut torque spec on 2004 doge ram 1500 4x4

Here are the specs you're looking for:
• Font axle to hub nut torque 185 ft-lbs
• Front hub bearing bolts 60 ft-lbs
• Caliper housing bolts 125 ft-lbs
• Caliper guide bolts 26 ft-lbs
• front spindle hub nut 97 ft-lbs
• lug nuts 100 ft-lbs.
0helpful
1answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4

The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

3helpful
2answers

Replace front left wheel berring on 2002 GMC Yukon

do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec
14helpful
1answer
10helpful
2answers

Torque specs

the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs
Not finding what you are looking for?

488 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...