Check engine light

Question edited for clarity and spelling.
Question mode to model category.

Mazda Tribute 2001-06 Firing Orders Repair Guide

AutoZone https://www.autozone.com > diy > mazda-tribute-2001...
3.0L engine Firing order: 1-4-2-5-3-6 Distributorless ignition; Fig. Coil and spark plug arrangement-2.3L engine; Fig. 2.0L engine Firing order: 1-3-4-2 ...

Mazda Tribute

mazdabg.com https://www.mazdabg.com > 9308CH10_Mazda_Tribute
Mazda Tribute. Fig. 14: 2.0L (VIN B) Engine Firing order: 1-3-4-2 Distributorless ignition system. Fig. 15: 3.0L (VIN 1) Engine Firing order: 1-4-2-5-3-6 ... Pictures

https://www.google.com/search?q=2001+Mazda+Tribute.+Firing+order

2004 Mazda tribute 2.0l manual transmission cranks position sensor tip worn / rubbing. p0351, p0352, p0500, p0320 codes. I have a 2004 Mazda tribute with 2.0l 4 cylinder. 140,000 miles. First problem was it would not start but I could hear the fuel pump run and the engine cranked over. I checked for spark and all four plugs had no spark. p0351, p0352, p0500, and p0320 codes displayed.
I have 12 volts at coil. I decided to remove and inspect crank sensor on the transmission side of the engine ( on engine below thermostat housing bolted to engine block) once i removed it i noticed the tip of the sensor was broken, yes, broken. so I knew i found the problem.
I put a new crank sensor in and the car started but ran for 1 hour idling as if a cylinder was not firing. Then it would not start ever again. I removed my brand new replacement sensor to find the tip was rubbed off enough to see the inside metal. i think it could be a possible warped flywheel but I am having trouble finding diagrams of the excitation part of how the crank position sensor works.
I believe the flywheel has holes that excite the sensor. The tribute does move and clutch works for the hour I had it running, so the manual Trans does work as well as the clutch.
https://electronicshelponline.blogspot.com/

Search Results

Failure of EGR Differential Pressure Sensor : Mazda Tribute ...

repairpal.com > Problems > Mazda > Tribute
Check Engine Light and Hesitation or Stumbling While Driving on Mazda Tribute ...this is my second egr valve and car is not picking up the right sped and when ... Mazda Tribute 2003, replacing burnt DPFE, connector bunrt, Need color pinout. ... Drivetrain · Electrical & Lights · Engine · Exhaust & Emissions · Heating & AC ...

Check Engine Light Diagnosis Cost for Mazda Tribute ...

repairpal.com > Estimator > Mazda > Tribute
A Check Engine Light is turned on when the Mazda Tribute engine control module detects a fault in the emissions system. One or more diagnostic codes will be

I would replace the engine and transmission mounts, they are hard and transmitting engine vibration to the chassis.

Hello - FIRST
Get the codes read.
Go to your local auto parts store, typically they read the obd II codes for FREE! This will NARROW it down a little..
Best regards
Ck

no
I would be looking at dirty /faulty injectors and fuel pressure problems

probable a coil take it to autozone an they will put on a test an tell with one for free

CHECK TRANSMISSION FLUID LEVEL FIRST.MAKE SURE ITS NOT LOW IF ALL IS GOOD YOU HAVE INTERNAL TRANSMISSION PROBLEM LIKE DAMAGE PLANETARY CARRIER ASSEMBLY.

The plastic rod ends on the cable assy that goes between the shft lever in the colum and the transmittion are worn. I change the cable for the same reason last week and that fixed the problem.
The cable part number is MZEC01-46-500E the price from the Mazda dealer was US $ 64.98. Is easy to change all you need is aphillips screw driver & pliers