P0107 map sensor circuit

Question edited to fix P-zero-one-zero-seven.

What the P0107 code means. P0107 is the general code for a problem with the MAP circuit sensor having too low voltage input to the Engine Control Unit (ECU). This means the voltage input to the ECU is . 5 volt or less which means that it is not in the correct lower range for proper engine operation.Mar. 12, 2016

P0107 OBD-II Trouble Code: Manifold Air Pressure ... - Autoblog

Videos as well

https://www.google.com/search?q=code+P0107

..

code p 0107 refers to manifold absolute pressure (MAP) sensor/ barometric pressure (BARO) sensor--low input===causes wiring short to ground---map sensor--baro sensor---ECM
code p 0122 refers to
(1)throttle position(TP) sensor A/ pedal position (APP) sensor A --low input ===causes ---wiring short to ground --TP/APP sensor/s---ECM
(2)TP switch and APP switch A--low input===causes -same as (1)
(3) TP sensor B/accelerator pedal position switch B---circuit malfunction====causes --wiring open/short to ground/short to positive--TP/APP switch--- ECM

Manifold Absolute Pressure (MAP) Sensor circuit low voltage.
I would check the wire connection at the map sensor, make sure it is still connected.

MAP SENSOR LOW VOLTAGE!!

What does that mean?

The Manifold Absolute Pressure (MAP) sensor responds to changes in the intake manifold pressure (vacuum). 5 Volts is supplied to the sensor from the PCM (powertrain control module). Inside the MAP sensor is a resistor that moves in relation to manifold pressure. The resistor varies the voltage between about 1 volt to 4.5 volts (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. A P0107 DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Potential Symptoms

Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include:

• Hard to start
• Long cranking times
• Sputtering/missing
• Blowing black smoke
• Poor fuel economy
• Dies intermittently
• MIL(Malfunction Indicator Lamp) illumination

Causes

The causes of a low MAP sensor signal circuit (P0107) could be any of the following:

• Bad MAP sensor
• Open or short in the signal circuit
• Open or short in the 5 Volt reference circuit
• Ground circuit open or shorted
• Bad PCM

P0107 -- CONTINUOUS
Continuous diagnostic trouble code P0107 indicated barometric pressure out of range low was detected during normal operation.

Possible cause - faulty internal BARO sensor (PCM)

Perform KOEO On-Demand Self Test. Is P0107 present?
Yes, REPLACE PCM. CLEAR DTC and RETEST.
No, P0107 is intermittent fault. CLEAR DTC. If DTC reappears, REPLACE PCM.

If you keep getting it, a new PCM is the only fix.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Check for a shorted wire harness laying on top of the a/c compressor line down by the compressor. The harness will sometimes lay on the line and wear through shorting out the 5 volt reference.

P0029 - Exhaust Valve Control Solenoid Circuit Range/Performance Bank 2
Causes:
- Dirty engine oil
- Low engine oil level
- Exhaust valve control solenoid circuit open or shorted
- Exhaust valve control solenoid circuit poor electrical connection
- Faulty exhaust valve control solenoid

Solutions:
- Change oil
- Replace exhaust valve control solenoid

P0047 - Turbocharger/Supercharger Boost Control A Circuit Low
This vehicle is not equipped with a turbocharger or supercharger if it is a 1994.

P0137 - o2 Sensor Circuit Low Voltage Bank 1 Sensor 2
Causes:
- Sensor circuit harness or connectors is open or shorted
- Rear heated oxygen sensor Bank 1 may be faulty
- Fuel pressure may be faulty
- Fuel injector may be faulty
- Intake air leaks

Solution:
Replacing the O2 Sensor 2 usually takes care of the problem.

P0107 - Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
Causes:
- Damage harness or connectors
- MAP sensor circuit is open or shorted
- MAP sensor
- Damaged PCM or ECM

Solutions:
- If damage, repair MAP sensor harness or connector
- Replace MAP sensor
- Replace PCM or ECM

P0107 - Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

The Manifold Absolute Pressure (MAP) sensor responds to changes in the intake manifold pressure (vacuum). 5 Volts is supplied to the sensor from the PCM (powertrain control module). Inside the MAP sensor is a resistor that moves in relation to manifold pressure. The resistor varies the voltage between about 1 volt to 4.5 volts (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. A P0107 DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low.

Potential Symptoms: Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include:
* Hard to start
* Long cranking times
* Sputtering/missing
* Blowing black smoke
* Poor fuel economy
* Dies intermittently
* MIL(Malfunction Indicator Lamp) illumination

Causes: The causes of a low MAP sensor signal circuit (P0107) could be any of the following:
* Bad MAP sensor
* Open or short in the signal circuit
* Open or short in the 5 Volt reference circuit
* Ground circuit open or shorted
* Bad PCM

Possible Solutions: First, using a scan tool with the Key on and engine running, monitor the MAP sensor voltage. If it is reading less than .5 volts, turn engine off, unplug the MAP sensor and, using a DVOM (Digital Volt/Ohm Meter) check for 5Volts on the 5 Volt reference circuit.

1. If there is not 5 Volts on the reference circuit, then check for the reference voltage at the PCM connector. If it is present at the PCM connector but not the MAP connector, repair the open in the reference circuit between the PCM and MAP harness connector. If 5 Volt reference is NOT present at the PCM connector, check powers and grounds of PCM and repair/replace as needed. (NOTE: On Chrysler products, a shorted Crank sensor, Vehicle speed sensor or any other sensor that utilizes the 5 Volt reference from the PCM can short out the 5 Volt reference. To fix simply unplug each sensor one at a time until the 5 Volt reference reappears. The last sensor unplugged is the shorted sensor.)

2. If you have a 5 Volt reference at the MAP connector, jumper the 5 volt reference circuit to the signal circuit. Now check the MAP voltage on the scan tool. It should be 4.5 to 5 Volts. If it is, replace MAP sensor. If not, repair open/short in the signal circuit wiring and re-check.

3. If all appears okay, perform a wiggle test. Start engine and manipulate the harness, connector and tap on the MAP sensor. Note any changes in voltage or engine speed. Repair connector, harness, or sensor as needed.

4. If the wiggle test checks out, use a vacuum pump (or just use your lungs) to draw a vacuum on the MAP sensor vacuum port. As you add vacuum the voltage should decrease. With no vacuum, the MAP sensor should read approximately 4.5 volts. If there is no change in MAP sensor reading on the scan tool, replace MAP sensor.

MAP Sensor DTC's: P0105, P0106, P0107, P0108 and P0109.

Hope helps (remember rated and comment this).

The Manifold Absolute Pressure (MAP) sensor responds to changes in the intake manifold pressure (vacuum). 5 Volts is supplied to the sensor from the PCM (powertrain control module). Inside the MAP sensor is a resistor that moves in relation to manifold pressure. The resistor varies the voltage between about 1 volt to 4.5 volts (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. A P0107 DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low.

Potential Symptoms Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include:

• Hard to start
• Long cranking times
• Sputtering/missing
• Blowing black smoke
• Poor fuel economy
• Dies intermittently
• MIL(Malfunction Indicator Lamp) illumination

Causes The causes of a low MAP sensor signal circuit (P0107) could be any of the following:

• Bad MAP sensor
• Open or short in the signal circuit
• Open or short in the 5 Volt reference circuit
• Ground circuit open or shorted
• Bad PCM

Possible Solutions First, using a scan tool with the Key on and engine running, monitor the MAP sensor voltage. If it is reading less than .5 volts, turn engine off, unplug the MAP sensor and, using a DVOM (Digital Volt/Ohm Meter) check for 5Volts on the 5 Volt reference circuit.
1. If there is not 5 Volts on the reference circuit, then check for the reference voltage at the PCM connector. If it is present at the PCM connector but not the MAP connector, repair the open in the reference circuit between the PCM and MAP harness connector. If 5 Volt reference is NOT present at the PCM connector, check powers and grounds of PCM and repair/replace as needed. (NOTE: On Chrysler products, a shorted Crank sensor, Vehicle speed sensor or any other sensor that utilizes the 5 Volt reference from the PCM can short out the 5 Volt reference. To fix simply unplug each sensor one at a time until the 5 Volt reference reappears. The last sensor unplugged is the shorted sensor.)
2. If you have a 5 Volt reference at the MAP connector, jumper the 5 volt reference circuit to the signal circuit. Now check the MAP voltage on the scan tool. It should be 4.5 to 5 Volts. If it is, replace MAP sensor. If not, repair open/short in the signal circuit wiring and re-check.
3. If all appears okay, perform a wiggle test. Start engine and manipulate the harness, connector and tap on the MAP sensor. Note any changes in voltage or engine speed. Repair connector, harness, or sensor as needed.
4. If the wiggle test checks out, use a vacuum pump
(or just use your lungs) to draw a vacuum on the MAP sensor vacuum port. As you add vacuum the voltage should decrease. With no vacuum, the MAP sensor should read approximately 4.5 volts. If there is no change in MAP sensor reading on the scan tool, replace MAP sensor.