Question about 2000 Chevrolet Silverado 1500

Open Question

Rear main seal plate torque specs - 2000 Chevrolet Silverado 1500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Juan Guillen

  • 373 Answers

SOURCE: 2005 chevy 4x42500hd

Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...

Posted on Nov 04, 2008

Ad

Anonymous

  • 379 Answers

SOURCE: torque specs.

connecting rod = first pass 18 ft lbs , second pass 75 degrees

main bearings = first pass 37 ft lbs , second pass 77 degrees

wow that wasn't easy to find for some reason .

Posted on Jan 01, 2009

Anonymous

  • 22 Answers

SOURCE: pinion nut torque spec chev

Axle Preload and Backlash Specifications 8.0 Axle Preload and Backlash Specifications Application
Specification
Metric
English
Backlash
0.08-0.25 mm
0.003-0.010 in
Backlash (Preferred)
0.13-0.18 mm
0.005-0.007 in
Pinion Bearing Preload, New Bearings
1.7-3.4 N·m
15-30 lb in
Pinion Bearing Preload, Used Bearings
1.1-2.3 N·m
10-20 lb in
Pinion and Differential Case Bearing Preload, New Bearings
3.4-6.2 N·m
30-55 lb in
Pinion and Differential Case Bearing Preload, Used Bearings
2.8-5.1 N·m
25-45 lb in

Posted on May 20, 2009

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

Lyle D. Rowh

  • 743 Answers

SOURCE: torque specs on Chevy Silverado 2500 rear diff yoke.

There isn't a torque spec since those bearing are pre-loaded. You place the unit on a good known vic and get a breaker bar and you might even have to put an extention on that and you begin to tighten unitil you fell the bearing start to load...a little extra short turn wouldn't hurt at that point.

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 altima 3.5 rear main seal leaking very bad, do i remove tranny or engine to get to seal area ? i have a 4 post lift, but no 2 post


Any vehicle with a rear main seal leaking, you must remove the transmission if the seal is one piece, goes in from the back. you'll need remove the flywheel/flex-plate to change the seal. Older versions you had to drop the oil pan and the rear main cap to replace a 2 piece seal. Take everything off the top of the trans to access the top mounting bolts and remove them. Support the engine and remove the trans mount. Pull the cover off the torque converter and remove the flex-plate to torque converter bolts then remove the rest of the trans bolts at bell housing and pull the trans out. You can use a transmission jack or like I do, just set the trans on top of a metal case on top of a barrel so you don't have to drop it all the way out. Just slide it out far enough to change the seal and put it back together.

Sep 02, 2018 | Cars & Trucks

1 Answer

What are the steps in replacing the rear seal in a 1966 ford f-100 with a 352 engine?


I wouldn't be surprised if you didn't have to remove the engine/transmission, split the trans from the engine, remove the TC or clutch/pressure plate, (you should have drained engine oil and auto trans oil before doing this), remove the oil pan, remove the rear most main bearing cap, rotate a new seal into place, replace rear main bearing cap, torque, etc. and reassemble.

Worst case you may have to remove harmonic balancer and front timing chain cover, front seal, release all the connecting rod caps and main bearing caps, remove the crankshaft, replace the rear main seal and reassemble. It's a 1966 engine...you should consider replacing the front timing chain with a roller chain as well as rod and main bearing inserts if you have to do all this.

Feb 04, 2017 | Ford Cars & Trucks

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Torque spec's for the fly wheel


Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Cars & Trucks

1 Answer

Torque pattern for rear main seal housing for 2000 chevy 4.8l


The pattern is a cross pattern, just like on a wheel. But I do not know how tight the bolts are suppose to be.

Jan 20, 2015 | Cars & Trucks

1 Answer

How to remove rear main seal from a 76 mercury monarch


Remove the oil pan. Remove the rear main bearing cap. Loosen the other main bearing caps. Using a special tool that resembles a chinese finger lock pull out the top part of the seal. It's a "rope" seal. Install the new seal in the block and the cap. Replace rear cap, torque all the main bearing caps to spec. Reinstall the pan. This job is pretty big for a novice - I don't recommend you try unless you have unlimited patience.

Jun 23, 2014 | Cars & Trucks

1 Answer

Rear barring an seal replaced


I'm not sure if this is the right part of your car but, are you talking about the rear seal on the engine for the crankshaft?

If so:

Rear Main Oil Seal REMOVAL & INSTALLATION Fig. 1: Rear main seal installation for the 2.3L and 2.5L engines 85553306.gif
Fig. 2: Removing the rear main seal 85553307.gif
Fig. 3: Installing the rear main seal on the 2.9L engines 85553308.gif
If the crankshaft rear oil seal replacement is the only operation being performed, it can be done in the vehicle as detailed in the following procedure. If the oil seal is being replaced in conjunction with a rear main bearing replacement, the engine must be removed from the vehicle and installed on a work stand.
  1. Remove the starter.
  2. Remove the transmission from the vehicle, following the procedures in Section 7.
  3. On a manual shift transmission, remove the pressure plate and cover assembly and the clutch disc following the procedure in Section 7.
  4. Remove the flywheel attaching bolts and remove the flywheel and engine rear cover plate.
  5. Use an awl to punch two holes in the crankshaft rear oil seal. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. Install a sheet metal screw in each hole. Use two large screwdrivers or small pry bars and pry against both screws at the same time to remove the crankshaft rear oil seal. It may be necessary to place small blocks of wood against the cylinder block to provide a fulcrum point for the pry bars. Use caution throughout this procedure to avoid scratching or otherwise damaging the crankshaft oil seal surface. To install:
  6. Clean the oil seal recess in the cylinder block and main bearing cap.
  7. Clean, inspect and polish the rear oil seal rubbing surface on the crankshaft. Coat a new oil seal and the crankshaft with a light film of engine oil. Start the seal in the recess with the seal lip facing forward and install it with a seal driver. Keep the tool, T82L-6701-A (4-cyl. engines) or T72C-6165 (6-cyl. engine) straight with the centerline of the crankshaft and install the seal until the tool contacts the cylinder block surface. Remove the tool and inspect the seal to be sure it was not damaged during installation.
  8. Install the engine rear cover plate. Position the flywheel on the crankshaft flange. Coat the threads of the flywheel attaching bolts with oil-resistant sealer and install the bolts. Tighten the bolts in sequence across from each other to the specifications listed in the torque chart in this section.
  9. On a manual shift transmission, install the clutch disc and the pressure plate assembly following the procedure in Section 7.
  10. Install the transmission, following the procedure in Section 7.
prev.gif next.gif

Oct 07, 2010 | 1994 Ford Explorer Limited

1 Answer

Torque specs for the main rear seal on a 2000 dodge caravan???


i am the owner of Alexander's Garage yu may contact me at 717-242-1749.

Feb 20, 2010 | 2000 Dodge Caravan

1 Answer

Losing oil form flywheel end of crankshaft. Already changed seal twice but ain't made any difference. any suggestions?


yes , depending on wheter you talking about torque converter seal or rear engine main seal , on trans if your front pump bushing has excessive wear then it will not seal because the torque converter input shaft will ride on seal more than it is supposed to and also it will not run true, also check TC mounting of flex plate if you flex plate is not centered then it will rotate out of balance and cause leaks and pump damage, if you talking about a rear main engine seal you may have a issue with run out and or bearing wear issues cause seal to not be able to do its job, check all those issues, crank shaft end play as well as up and down play and check rotational run out on TC of trans and pump bushing in trans pump... hope this helps, thanks please rate...

Aug 07, 2009 | 2001 Hyundai Accent

2 Answers

How toreplace rear main seal in 92 F150 4.9 inline 6


One thing you may want to try especially if you don't have a heated garage is a bottle of Bar's leak rear main sealer. I had a leak big enough to cause my clutch to slip and it worked for me. I figure in the spring I'll replace the seal, maybe.

Oct 04, 2008 | 1992 Ford F150 SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...