2000 Toyota 4Runner Logo
Posted on Mar 08, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Drivers door power lock wont work.

My drivers door power lock wont work on my 2000 toyota 4 runner. I have tried locking and unlocking with the door lock button on the control panel and also with the auto key remote lock and unlock button. The only way it will work is to manually open it with the key itself. All 3 of the other door locks unlock and lock fine from both the control panel and the remote device....HELP!

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Sniper:

An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert 104 Answers
  • Posted on Mar 09, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Sniper:

An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

Joined: Dec 11, 2008
Answers
104
Questions
8
Helped
69956
Points
336

Either the wring going to that motor or the motor itself is bad.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

1994 toyota 4 runner electric windows will stop working wont roll up or down then sometimes work again. the electric locks also aree not working properly if i push the driver door lock it unlocks al

It is a common problem that may be quickly remedied. Try this....spray your door hinges with a good penetrating oil...then work them back nd forth as to open and close. You are possibly losing ground.Also check to be sure you have a good ground from the body to engine.Hope this helps
0helpful
1answer

I have a 2003 Toyota 4-Runner. The keyless alarm has stopped working on the drivers side door.

On the driver side the actuator is more likely the culprit,the linkage could of come off or the actuator just doesnt work
9helpful
2answers

Power door locks for 1999 toyota 4runner unlock but do not lock on inside switches or remote

I have the same problem I can unlock my toyota 99 4 runner but does not lock on inside switches or remote.

just found out about it today.
1helpful
1answer

1998 Toyota 4runner driver side power door lock problem.

probably gonna have to take the door panel off. You say it wont unlock or lock with the key? if thats the case its probably broke inside the door.
4helpful
2answers

2000 Toyota Sienna Minivan car alarm goes off.

1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.
Not finding what you are looking for?

1,165 views

Ask a Question

Usually answered in minutes!

Top Toyota Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

926 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...