Hi ,, I need to know if my alarm is turned of or if the module is bad in my land rover freelander. can some one tell me where i can find it

Land Rover Freelander 2002-2005 KV6 Timming belt and ...

? 4:31
https://www.youtube.com/watch?v=sz_oe9tIFH4
Jul 3, 2011 - Uploaded by Jaime Depaula
Land Rover Freelander 2002-2005 KV6 Timming belt andreplacing valves - Video 2 ... shops in North Eastern USA for bent valves and timing belt change? .... Land Rover 200tdiTiming Belt -From Broken Belt to Retiming the ...

ROVER K Series Cambelt Change Video - YouTube

? 10:52
https://www.youtube.com/watch?v=1Qn8ljQKZxA
May 4, 2012 - Uploaded by metalworker007
How to change a rover K series cam belt .. by Technozen of ...soy espa?ol porfavor quiero saber timing marks de MG ROVER 25 petrol 1795cc engen .... Hi, Have a Land Rover Freelander1999 petrol serie K, that dont start, ...

Freelander 1.8i timing belt - Land Rover Technical Archive - LR4x4 ...

forums.lr4x4.com > ... > Tech Archive > Land Rover Technical Archive

Nov 20, 2006 - 1 post - ‎1 author
The following is instructions for replacing the timing (or camshaft) belt on the 1.8i petrol engine, as fitted to a Freelander. This is the K-series ... With the timing set, thecam sprocket marks should look like this. Posted Image

How to Replace timing belt on Land Rover Freelander 2.5 ...

Check the ignition barrel electrical connections before doing anything, they are a common fault and do detach and cause wiring shorts, this fools the vehicle into thinking its being stolen. There is also a unit situated behind the dashboard clocks which are also a known common fault, its part of the immobilizer and also are well known to short out when being jump started with leads or a booster pack, it isnt coded. Hope it helps good luck.

There is no telling what all you burned out from this mistake, how does someone do this???, you could have destroyed every electronic module in the car.

Need reliable Land Rover Freelander parts? ... The Land Rover Freelander was introduced to the market as a premium ... Land Rover Replacement Antenna ... www.carpartswholesale.com/cpw/land_rover~freelander~parts.html www.carpartswholesale.com/cpw/land_rover~freelander~parts.html
I have just gone into this site. They seem to have everything you could possibley need for yr Land rover - hope your are successful

Hi always use fully sinfetic,if not shore just give land rover a call and they will tell you the best oil for this motor.
(sorry about the spelling,all the best.

The Freelander is Land Rover's entry-level crossover SUV. Unlike other Land Rover vehicles that use a traditional "truck," body-on-frame chassis, the Freelander is built on a unibody, front-wheel drive car chassis. The Freelander is sometimes known in the U.S. as the "LR2."

1 Purchase replacement bulb P21/5W, available at most auto parts stores and at any Land Rover
dealer.

2 Turn off engine and open rear cargo door.

3 Remove the two Torx screws from the side of the tail light assembly. Carefully pull the assembly
away and unplug the electrical harness.

4 Turn the assembly over to access the bulb modules. There are three separate bulb modules; the
top module should be the brake light.

5 Rotate the bulb module counterclockwise to release it from the tail light assembly. Push the bulb
down (into the module) and turn it counterclockwise to remove it from the module.

6 Insert the new bulb into the bulb module. Carefully push the bulb down and turn it clockwise.
Reinsert the bulb module into the tail light assembly and turn it clockwise.

7 Reconnect the electrical harness to the tail light assembly. Remount the tail light assembly and
replace the Torx screws.

dont know what a 51 plate is ,a 51 land rover would be manual adjusters with a B series engine which would be 12 inlet and 15 exhaust .points gap would be lucas 15th and plugs would be 25th ,didnt know they used this name freelander in 1951 ,come to think of it i didnt think they made land rovers till the middle 50s

there is a module mounted on the fan shroud that is a common problem. but as always, check fuses, connectors and grounds!

Hi have you any idea what is a torque wrench and do you have any experiment in car engine repairing? this not easy and cheap to whom have no tools ,let me know more.