Question about 2002 Chrysler Town & Country

1 Answer

Removing the windshield washer reservoir in a 2002 Chrysler T&C

How do I remove the windshield washer resevoir on my 2002 Chrysler
T & C minivan to replace washer pump?

Posted by on

  • 2 more comments 
  • Anonymous Mar 19, 2014

    if I have a 2002 Chrysler minivan if I change the speedometer or the cluster will it change the miles

  • Anonymous Mar 19, 2014

    on a 2002 Chrysler minivan if I change the cluster will it change the miles

  • Anonymous Mar 19, 2014

    2002 Chrysler minivan if I change the speedo cluster will it change the miles

  • Anonymous Mar 19, 2014

    busted windshield reservoir

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 16 Answers

REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the engine fresh air housing inside the engine compartment.
  3. Disconnect the washer hose at the in-line connector forward of the cowl grille so that the in-line connector remains with the washer hose from the fresh air plenum.
  4. Disconnect the washer hose from the hose clip located on the front fender side shield.
  5. Remove the filler tube screw.
  6. Hoist and support vehicle on hoist or jack stands.
  7. Remove the right front wheel and tire assembly.
  8. Disconnect the left right front wheelhouse splash shield and move aside.
  9. Drain washer fluid from the reservoir and into a suitable clean container. This can be done by disconnecting the windshield washer hose from the front (outboard) washer pump and allowing the washer fluid to drain into a container through a temporary jumper hose connected to the front washer pump.
  10. Disconnect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the release position, then, depress the black tab and pull the connector off the pump or sensor.
  11. Remove the two reservoir mounting screws.
  12. Disconnect the reservoir from the body mount by raising the reservoir upward slightly and then down so that the reservoir filler neck and front washer hose pull through the opening in the front fender side shield.
INSTALLATION

  1. Push filler neck and front washer hose through the opening in the front fender side shield. Connect the reservoir to the body mount by lowering the reservoir down.
  2. Install the two reservoir mounting screws. Torque screws to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  3. Connect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the closed or locked position.
  4. Assure that washer is properly routed to prevent pinching and possible inoperative washers.
  5. Connect the left right front wheelhouse splash shield and move aside.
  6. Install the right front wheel and tire assembly.
  7. lower vehicle from hoist or jack stands.
  8. Install the filler tube screw. Torque screw to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  9. Connect the washer hose to the hose clip located on the front fender side shield.
  10. Connect the washer hose at the in-line connector forward of the cowl grille.
  11. Install the engine fresh air housing inside the engine compartment.
  12. Connect the battery negative cable.
  13. Verify system operation.

Posted on Apr 01, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the windshield washer pump located under the hood?


it locate in tthe bottom of windshield water reservoir(tank)

Mar 04, 2015 | Chrysler PT Cruiser Cars & Trucks

1 Answer

How do I replace the windshield washer resevoir on a 2004 Pontiac grand am?


Step 1:

Remove the drivers front wheel

Step 2:

remove the plastic inner fender well.

Step 3:

you will then see the washer reservoir. there will be one screw towards the front of the car thats behind the air tube that you will have to feel for in order to find/remove. The other two bolts are can be clearly seen with the fender well removed.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Dec 15, 2012 | 2004 Pontiac Grand Am

1 Answer

2002 chrysler concorde evap cannister location


look engine compartment near cruise control actuator or look fender panel near windshield washer fluid reservoir.chrysler put EVAP CANISTER DIFFERENT PLACES.

Dec 15, 2012 | 2000 Chrysler Concorde

1 Answer

2000 nissan xterra...windshield washer fluid pump motor has failed. How do I get to and replace the motor?


On the drivers side of the vehicle just behind the front bumper is the washer fluid reservoir. The washer pumps (2 - one for the back and one for the front) are located ont the face of the reservoir.

1) Drain the resevoir. (You can reuse this fluid, so put it in a clean container)
2) Disconnect the wiring harness for the problem pump.
3) Remove the sprayer line.
4) Remove the pump. It is held in by being snapped into a channel on the resevoir and by the rubber grommet. This may take some elbow grease.
5) Remove the old grommet.(If your new pump came with a new grommet)

Installation is reverse. Usually new pumps come with new grommets. If not, it is ok to reuse the old one.

Jan 25, 2010 | 2000 Nissan Xterra

1 Answer

Replace windshield washer resevoir on a 2000 ford windstar


YOU CAN GO TO AUTO ZONE OR ADVANCE AUTO PARTS .BUY A HAYNES MANUAL FOR 2000 FORD WINDSTAR.IT WILL SHOW AND TELL YOU HOW TO FIX WINDSHIELD WASHER RESERVOIR.

Nov 11, 2009 | 2000 Ford Windstar

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Windshield washer fluid reservoir - MB ML 350


right where the lines connect to reservoir, has little black seals that leak. I recommend removing reservoir, empty it out, then use RTV silicone and place it between seals and reservoir. Let it dry for FULL day. than reinstall.

Jun 23, 2009 | Mercedes-Benz ML350 Cars & Trucks

2 Answers

Locate windshield washer motor


if you lie on the floor under the reservoir and look where the plastic is round under the wheel arch then you will see at the very bottom of reservoir is the offending motor. if you hear it start off but still no water then you mite just have a blockage. caution should be take when taking this off as it will squirt water all overt the place.

Feb 24, 2009 | 2002 Chrysler Voyager

2 Answers

Wiper fluid level sensor replacement


Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Jan 15, 2009 | 2000 Mercury Villager

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

1,227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...