Question about 1995 Mercury Mystique

1 Answer

Vacuum hose routing diagram

Need to know where a line goes. from the intake tube between the throttle body and the airbox. the hose is rotted off and the car is loosing a lot of vaccum. I need a diagram of were the hose connects too.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 45 Answers

It goes to the Pvc system. Usually onto a valve cover

Posted on Feb 06, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
asetech74

Ed Warden

  • 218 Answers

SOURCE: loose hose

This sounds to me like it may be a hose for some type of vacuum modulator that may be located within the transmission case. Look around the transmission on the underside of the car for any signs of any vacuum lines that may not be attached. It may also attach somewhere along the top of the transmission. Hope this helps.

Posted on Mar 12, 2009

Anonymous

  • 6 Answers

SOURCE: vacuum lines

is it a canister or a blow by hose for the transmission pan below the battery, if its mounted on top of the battery tie down its to the transmission pan

Posted on Jun 22, 2009

Anonymous

  • 1 Answer

SOURCE: Vacuum hose routing.

The emissions sticker does not show this hose.
This is a rubber hose that appears to have been attached to a port at some time.

Posted on Nov 17, 2009

mitchbtu

Mitch Hayes

  • 121 Answers

SOURCE: I found a vacuum hose hanging and dont know where

The correct diagram for your engine is located under the hood, Look on the radiator support, firewall, or sometimes on a valve cover...

Posted on Jan 27, 2010

Anonymous

  • 2 Answers

SOURCE: 2002 mercury cougar vacuum line off the top of transmission

The hose connects to the top of the transmission, underneath the car's battery (you'll have to remove the battery to see the connection site). It's important that this hose, once reconnected, does not does not get crimped. If the hose is not free to "breathe" pressure buildup in the transmission can cause fluid to pour out of the fill point (where the dip-stick goes).

Posted on Apr 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the fuel injector on a 2008 chrysler pt cruiser


Removal & Installation

Except Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release fuel system pressure.
  2. Remove the air cleaner lid, disconnect the inlet air temperature sensor and makeup air hose.
  3. Remove the negative battery cable.
  4. Remove the engine cover or throttle control shield if equipped.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  5. Disconnect fuel supply tube from rail.
  6. Remove the Intake Manifold, refer to the Engine section.
  7. Disconnect electrical connectors from fuel injectors.
  8. Remove bolts holding fuel rail.
  9. Remove the fuel rail and injectors.
  10. Remove the injectors from the fuel rail.
To install:
  1. Install injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  4. Attach electrical connectors to fuel injectors.
  5. Connect fuel supply tube to fuel rail. Refer to Quick Connect Fittings in the Fuel Delivery section
  6. Install Intake Manifold, refer to the Engine section.
  7. Install the engine cover or throttle control shield if equipped.
  8. Install the negative battery cable.
  9. Install the air cleaner lid, connect the inlet air temperature sensor and makeup air hose. Tighten air inlet tube clamps to 20-30 inch lbs. (2-4 Nm).

Turbocharged Models

WARNING Release fuel system pressure before servicing fuel system components. Service vehicles in well ventilated areas and avoid ignition sources. Never smoke while servicing the vehicle. This may result in personal injury or *****.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Disconnect the throttle body inlet hose and remove from throttle body.
  4. Disconnect the purge hose from the throttle body.
  5. Unlock and disconnect the electrical connection at the throttle body.
  6. Remove the throttle control shield .
  7. Remove the throttle and speed control cables from the throttle body.
  8. Remove the cables from the throttle body bracket.
  9. Unlock and disconnect the MAP sensor electrical connector.
  10. Remove the vacuum lines from the rear of the intake manifold.
  11. Remove the 5 bolts from the front of the intake manifold.
  12. Remove the 2 bolts from the rear of the intake manifold.
  13. Remove the intake manifold. Cover the lower intake manifold openings.
  14. Drain the Coolant system.
  15. Move the upper radiator hose clamp, so that the hose can be rotated up and out of the way.
  16. Remove the 2 small hoses from the thermostat housing.
  17. Remove the 2 bolts from the thermostat housing and rotate the assembly up and out of the way.
    NOTE Wrap shop towels around hose to catch any gasoline spillage.
  18. Disconnect the fuel line from the fuel rail.
  19. Unlock and disconnect the electrical connectors from the fuel injectors.
  20. Remove the wiring harness from the fuel rail.
  21. Remove the 2 bolts from the fuel rail.
  22. Remove the fuel rail and injectors from the intake manifold.
To install:
  1. Install the fuel injectors to the fuel rail.
  2. Apply a light coating of clean engine oil to the O-ring on the nozzle end of each injector.
  3. Insert fuel injector nozzles into openings in intake manifold. Seat the injectors in place.
  4. Install the 2 bolts to the fuel rail. Tighten fuel rail bolts to 170-230 inch lbs. (19.5-25.5 Nm).
  5. Install the wiring harness to the fuel rail.
  6. Connect and lock the electrical connectors to the fuel injectors.
  7. Connect the fuel line to the fuel rail.
  8. Rotate the assembly back into place and install the 2 bolts to the thermostat housing tighten to 110 inch lbs. (12.5 Nm).
  9. Move the upper radiator house clamp back into place.
  10. Install the 2 small hoses to the thermostat housing.
  11. Fill the Coolant system.
  12. Install the intake manifold.
  13. Install the 2 bolts to the rear of the intake manifold tighten to 250 inch lbs. (28 Nm).
  14. Install the 5 bolts to the front of the intake manifold and tighten to 250 inch lbs. (28 Nm).
  15. Install the vacuum lines to the rear of the intake manifold.
  16. Connect and lock the MAP sensor electrical connector.
  17. Install the cables to the throttle body bracket.
  18. Install the throttle and speed control cables to the throttle body.
  19. Install the throttle control shield.
  20. Connect and lock the electrical connections at the throttle body.
  21. Connect the purge hose to the throttle body.
  22. Connect the throttle body inlet hose to the throttle body and tighten clamps to 20-30 inch lbs. (2-4 Nm).
  23. Connect the negative battery cable.
  24. Use the DRB® scan tool ASD Fuel System Test to pressurize the fuel system. Check for leaks.

Mar 02, 2017 | Chrysler Cars & Trucks

1 Answer

Vacuum diagram for a 2004 tiburon


There is only 4 vacuum lines on that engine

1- brake booster line

2- purge line to purge solenoid (top center of throttle body)

3- PCV hose. run straight from PCV to side of intake at base of throttle body

4- fuel pressure regulator line (short small diameter hose runs from #6 intake runner to fuel pressure regulator

5- tube that connects front cam cover to rear cam cover to improve vapor venting

http://www.hyundai-forums.com/attachments/gk-tiburon-coupe-s111-2003-2008/38204d1276396353-vacuum-lines-2004-tiberon-pict0001.jpg

Jun 25, 2012 | Hyundai Tiburon Cars & Trucks

1 Answer

I need a vacuum line diagram fo a 1996 Chevy Lumina, 3.1. One line that is not connected to anything, is located at the top of the engine.


Sorry I don't have the diagram, but I do have a diagram of the engine and component locations. Your vacuum system is fairly simple. You have a MAP sensor attached to the air cleaner. I have pasted a picture below. It has one electrical connector and one vacuum hose that goes to the intake manifold or the throttle body.
Behind the right headlight is your evap canister. This will have a hose or line running to the fuel tank. Then it will have another hose going to the purge valve. The purge valve should be close by and it has a connector plus another hose that goes to the intake manifold.
Then you have the PCV hose that goes from the PCV valve in the valve cover to the air cleaner or intake manifold. I think yours just has a hose from the air cleaner and the rest is internal.
There is one more vacuum hose, and that is the bog one that goes from the intake manifold (or throttle body--looks to me like there are a couple of vacuum ports on the back side of the throttle body, and there may be a "T" on one of the hoses) to the brake booster. It this one was off, the engine would not run, as the vacuum draw is large. Please let me know if you cannot figure it out from these instructions and provide a picture, if you can.

MAP sensor:
jturcotte_653.jpg

purge valve:
jturcotte_654.jpg

jturcotte_2455.gif
jturcotte_2456.gif

Oct 30, 2011 | 1996 Chevrolet Lumina Mini

2 Answers

Having trouble locating the iddle air control motor


the IAC valve is located directly on the throttle body, which is connected to the airbox by a rubber hose/tube

good luck!

Mar 01, 2011 | 2002 Mercury Cougar

2 Answers

Where is throttle positioning sensor on a suzuki forenza


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the Intake Air Temperature (IAT) sensor connector.
  3. Disconnect the breather hose from the valve cover.
  4. Remove the air intake tube.
  5. Disconnect the throttle cables by opening the throttle and moving the cable through the release slot.
  6. Disconnect the vacuum hoses from the throttle body.
  7. Disconnect the Throttle Position (TP) sensor and the idle air control valve connectors.
  8. Disconnect the coolant hoses from the throttle body.
  9. Remove the throttle body and discard the gasket.
  10. Remove the TP sensor.
  11. Remove the Idle Air Control (IAC) valve.
  12. Remove the throttle body retaining nuts.
  13. Remove the throttle body.

To install:

  1. Install the throttle body.
  2. Connect the TP sensor connector and the IAC valve connector.
  3. Connect the coolant hoses to the throttle body.
  4. Connect the vacuum hoses to the throttle body.
  5. Connect the throttle cable.
  6. Install the air intake tube.
  7. Connect the breather hose to the valve cover.
  8. Connect the IAT sensor connector.
  9. Connect the negative battery cable.
  10. Fill the cooling system
  11. shinehutt_33.gif
  12. i hope this helps tps is attatched to hrottle body on other side than throttle cable
  13. plz dont forget to vote rep[ly if you need more help

Jan 17, 2011 | 2006 Suzuki Forenza

1 Answer

Need diagram of under the hood of a 98 XK8 Jag...looking for the throttle body


hello
if you locate the airbox fitted to the Right hand inner wing you will see a large black intake pipe leading to the centre rear end of the engine bay that is where the throttle body is located if you remove this pipe by removing the hose clip securing the intake pipe of the air mass meter and then follow the pipe back to the centre rear of the engine bay and the pipe is attached to the throttle boy with 2 10mm hex bolt once these bolts are removedand the intake pipe is removed the throttle body is evident
Regards

Jan 08, 2011 | Jaguar XK8 Cars & Trucks

2 Answers

I would like to clean my tps and mafs. where can i locate these. it is 98 early model


The tps is located on the side of the throttle body, usually black in color and has 2 screws or bolts and a wire connection. Uaually they can't be cleaned, they are a sealed unit.
The maf sensor is in the intake tube that goes from the air filter housing to the throttle body.

Nov 20, 2009 | 1998 Audi A4

1 Answer

Need to know were the throttle sensor unit is located


ok, this is a fairly easy thing to find. ill try to explain it in a simple way...start at your air filter under the hood. follow that long intake tube that runs to your engine from the airbox. it will be attatched to whats called the throttle body. its a small housing that is bolted on to the engines intake manifold. now on this housing, there will be a sensor mounted on the side with probably 3 or 4 wires attatched to it with a plug. this is your throttle position sensor.

Aug 31, 2009 | 1999 Volvo C70

2 Answers

Where are maf and map sensor located in a 2001 with l4 2.4l


it is always in the intake before the throttle body, sometimes in the plastic ducting hose leading into the intake airhorn. look for wires coming from the unit in this area, you should be able to track it down easily... please rate my help. thanks

Aug 07, 2009 | 2001 Kia Optima

1 Answer

Can I change the electronic idler motor on my 1998 camry or does it require


The air intake tube is the plastic or rubber hose that connects the air filter box to the throttle body. It should be about 3-4 inches in thickness..... The motor is relitivly easy to change. Although, you will need to remove the throttle body to change because it is located on the botton of the throttle body. Let me know if you have any problems.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jonathan_3a3c556b4b17d1d2

Aug 20, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1995 Mercury Mystique Logo

Related Topics:

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

fordexpert

Level 3 Expert

5692 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...