Honda torque converter clutch solenoid circuit

DTC P0740 Torque Converter Clutch (TCC) Enable Solenoid Control Circuit

Circuit Description
The torque converter clutch (TCC) solenoid valve is an electrical device that is used with the torque converter clutch pulse width modulation (TCC PWM) solenoid valve in order to control TCC apply and release. The TCC solenoid valve attaches to the transmission case assembly extending into the pump cover. The TCC solenoid valve receives ignition voltage through the ignition 0 voltage circuit. The powertrain control module (PCM) controls the solenoid by providing the ground path on the TCC solenoid valve control circuit. The PCM monitors the throttle position sensor voltage, the vehicle speed, and other inputs in order to determine when to energize the TCC solenoid valve.
When the PCM detects a continuous open, short to ground or short to power in the TCC solenoid valve circuit, then DTC P0740 sets. DTC P0740 is a type B DTC.

Check it out on youtube.

P0740 is the torque converter malfunction code. The converter is in between the engine and transmission. The fluid that you are seeing is transmission fluid. It needs to go to a mechanic to narrow it down from there.

This code is set when the transmission control module detects improper voltage at the torque converter clutch. This can be caused by low tranny fluid/dirty tranny fluid/defective torque converter clutch solenoid/electrical connections to from solenoid

On some cars, there is a TCC solenoid in the transmission which can be replaced by removing the bottom pan. In some cars this solenoid can't be accessed without major disassembly.

Error Code: P0740
Description:
Torque Converter Clutch (TCC) Solenoid - Circuit Malfunction
Possible Cause:
Wiring.
Torque converter clutch (TCC) solenoid.
Engine control module (ECM)/Powertrain control module (PCM)/Transmission control module (TCM).

P0740 Honda - Transmission Lock-Up Control System Fault Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness is open or shorted
- Torque converter clutch solenoid valve circuit poor electrical connection

Tech notes
On some Honda vehicles the P0740 code may be set by an overheating torque converter problem which is caused by an insufficient flow to the torque converter release circuit.

P0740 Honda Description
The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter.
Lock-up operation, however, is prohibited when A/T fluid temperature is too low.
When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

its the transmission linear solenoids not the torque converter solenoids. you can buy the linear solenoids on ebay for about $100

P0740 - Torque Converter Clutch Malfunctionhttp://engine-codes.com/p0740.htmlForum CodePossible causes- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted When is the code detected?Diagnostic trouble code P0740 is detected when TCM detects an improper voltage drop when it tries to operate the solenoid valve.

P0700 TCM has requested PCM to run on Check engine light to alert to a fault in the automatic transmission.

P0740 JEEP - Torque Converter Clutch Circuit
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission shift shock
- Vehicle may not shift into the highest gear

Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness or connectors
- Torque converter clutch solenoid valve circuit is open or shorted

When is the code detected?
Torque Converter Clutch (TCC) unlocked for 10 sec., ECM commands converter lock-up and did not record engine speed drop.

P0740 JEEP Description
The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter.

Lock-up operation, however, is prohibited when A/T fluid temperature is too low.

When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514