Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Oct 01, 2013

2008 1500 GMC sierra pick-up stabilitrak service traction control light comes on and it now rides rough

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Jul 07, 2009

SOURCE: Service Active Handling, ABS and Traction Control Lights on

I have had exactly the same problem on and off for 3 years now - and just solved it last week thanks to another computer site. Remove and disassemble both grounds from the top of both the left and right frame rails adjacent to the front corners of the engine block. Completely clean the green corrosion from the internal parts with fine sandpaper and add dielectric grease then re-assemble. Clean the mounting bolt and frame hole while you're at it. Sounds time consuming and difficult, but it ain't. No more than 45 minutes combined. I am a technical airhead so if I can do it so can you. What clued me in was the problem always occurred around wet or humid weather. Also, the clock would always lose time overnite. That has ceased also. Good luck. Anyone know why my left headlite, when deployed, vibrates and shimmys??? Sully [email protected]

Ad

Anonymous

  • 212 Answers
  • Posted on Feb 06, 2010

SOURCE: why does stabilitrak light come on saying service

It's telling you your stabilitrak system is not functioning properly. Sensors in system are failing and setting service light. You need a GM dealer to diagnose system.

Anonymous

  • 252 Answers
  • Posted on Feb 21, 2011

SOURCE: my 2002 impala's service traction control light

Traction control only works when one wheel is spinning faster than the other it trys to even them out so it wont spin...sometimes if one of the wheels come off the ground in an uneven area or if you take a turn too fast and one wheel turns when the other one dont it is designed to operate.
I would remove all wheels and check the braking system...Is it 4 wheel disc or rear drum ?
If it has rear drums you could have a wheel cylinder leak that will sometimes lock the wheel because of fluid contamination....This would cause both lights to come on...If you find no problems
sometimes the abs sensor builds up fragments on the magnet and makes the light come on...
or if the abs sensor is not close enough to the exciter ring it will make the light come on because it will be out of adjustment.....all you do is press the sensor inward until it barely touches the ring and it will adjust itself....You can sometimes clean the magnet if it is contaminated and make the light go off ( only after you reach 6 to 15 mph. it will go off ).If it dont go off you have to buy a sensor.
Also make sure all tires have same amount and plenty of air to keep vehicle in balance/level.

Anonymous

  • 1 Answer
  • Posted on Apr 13, 2011

SOURCE: On my 2007 Chevy Equinox

i have chevy equinox 2007 LT with AWD system, my problem is that i have two messages appearing in the DIC : satbilitrack and service tracktion control. can u help me with this and tell me whats the problem and how should i fix it?

wyet_helps

wyet

  • 510 Answers
  • Posted on May 21, 2011

SOURCE: my 2007 have a stabilitrak on and service traction...

I would advise to take it to a shop you trust and let them scan your vehicle for trouble codes. From there they can give you an idea as to why these messages appeared. : )

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My 2009 GMC Sierra SLE 4/4 K Series after starting the Service Traction Control & Service Stabilitrak light as well as the check engine light come on and stays on. How do I correct this?

Hook up a professional grade scan tool and read DTC'S - diagnostic trouble codes. then get service repair info. www.alldatadiy.com and do the diagnostic tests for that code. Thats how a professional tech does it.
0helpful
1answer

What is making my stabilitrak light staying on

StabiliTrak service light - Chevy TrailBlazer, TrailBlazer SS and ...

forums.trailvoy.com > ... > 02-09 General Tech Q&A > General

Dec 24, 2009 - 11 posts - ‎7 authors
However, the StabiliTrak system seems to be working, as in my area ... If you have OnStar push the button when the Service Stabilitrak light is on have them run a diagnostic. ... 2007 Chevy TrailBlazer LS .... Choose your make. Service Stabilitrak light comes on
11 posts
Mar 31, 2011
Service Stabilitrak
11 posts
Mar 27, 2011
very strange thing happend/ traction control light ...
8 posts
Sep 2, 2010
Abs and traction control light
11 posts
Sep 20, 2009
More results from forums.trailvoy.com
0helpful
1answer
0helpful
1answer

I had a problem with power steering leak . They changed the hoses and pump and reservoir and rack. Now I have stabilitytrac control light on and when you are stopped you can't turn the steering wheel.

Service Stabilitrak, Traction Control lights ON, alone with check ...

chevroletforum.com > ... > Equinox
Jul 9, 2012 - I have a 08 Equinox with 79000 miles on it, for the last few weeks or soI've been having the service traction control/ service stabilitrak light ... HELP - Service Stabilitrak & Service Traction Control - Chevrolet ...
Aug 30, 2011
Service Traction Control - Stabilitrak and ABS light, Help ...
Feb 12, 2011
More results from chevroletforum.com

How To COMPLETELY Disable Traction/Stabilitrack Control ...

? 6:16
https://www.youtube.com/watch?v=TUoV2ue7amY
Jul 7, 2013 - Uploaded by Kyle Riegle
How to completely disable traction control on gm/chevy trucks and suv's. ... I got to anaheim the light of the ...

Has anyone ever had the service stabilitrak, service traction ...



0helpful
1answer

I keep getting a message service stabilitrak

StabiliTrak Indicator Light: If the warning light does not come on then, have it fixed so it will be ready to warn you if there is a problem. If it stays on, or comes on when you are driving, there may be a problem with your StabiliTrak system and your vehicle may need service. When this warning light is on, the system is off and will not limit wheel spin. Adjust your driving accordingly.

This light will also flash when the StabiliTrak system is active. If the StabiliTrak system warning light comes on and stays on for an extended period of time when the system is turned on, your vehicle needs service.

The traction control part of StabiliTrak can be turned off by pressing and releasing the StabiliTrak button if both systems (traction control and StabiliTrak) were previously on. To disable both traction control and StabiliTrak, press and hold the button for five seconds.

Traction control and StabiliTrak can be turned on by pressing and releasing the StabiliTrak button if not automatically shut off for any other reason.

When the TCS or StabiliTrak system is turned off, the StabiliTrak light and the appropriate TCS off or StabiliTrak off message will be displayed on the DIC to warn the driver. Your vehicle will still have brake-traction control when traction control is off, but will not be able to use the engine speed management system.

If the StabiliTrak and/or Traction Control are not operating properly, I encourage you to take your vehicle in for inspection. A certified technician will be able to offer a more accurate diagnosis.
1helpful
1answer

Trying to find the location of the stabilitrak sensor on a 2011 sierra 2500hd 4wd

Abs light on normally its one of the wheel bearing in the front abs sensor are in the bearing you got to pass a scanner on the truck to find wish one is difective
0helpful
1answer

Noise coming from front end and ABS/Stabilitrak errors

sounds like your abs ring on the axle has come loose
0helpful
2answers

Stabilitrak off ,how to fix

You must have the system scanned with a special tool by the dealer before any repair can start.
13helpful
4answers

My service stabletrack keeps come on how to fix that

Hi there:

Your vehicle is equipped with StabiliTrak, which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Traction control activates when the controller senses wheel spin. StabiliTrak will selectively apply the brakes and reduce engine torque to help regain traction.


Stability control activates when the controller senses a discrepancy between your intended path and the direction the vehicle is travelling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to help guide the vehicle in the direction which you are steering.


When you first start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle. If driving conditions delay system initialization, the STABILITRAK NOT READY message may be displayed. If this is the case, your vehicle does not need servicing.


When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event.


You may also feel or hear the system working. This is normal.
StabiliTrak will turn off automatically if a problem is detected in the system. The StabiliTrak light will come on and SERVICE STABILITRAK will be displayed on the DIC. For vehicles without a DIC, the StabiliTrak light and the StabiliTrak service light will both come on. If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, you should see your dealer for service.


Hope this helps.
9helpful
1answer

I have a wrench with a car swerving light up every once in awhile but I have no idea what it means and I have no idea what stabilitrak is

{: ) A car swerving light on the instrument cluster is the StabiTrak indicator, sometimes called the traction control indicator. A wrench beside it tells it requires servicing.

Your vehicle is equipped with StabiliTrak, which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions.
Traction control activates when the controller senses wheel spin. StabiliTrak will selectively apply the brakes and reduce engine torque to help regain traction.
Stability control activates when the controller senses a discrepancy between your intended path and the direction the vehicle is travelling. StabiliTrak selectively applies braking pressure at any one of the vehicle's brakes to help guide the vehicle in the direction which you are steering.
When you first start your vehicle and begin to drive away, the system performs several diagnostic checks to insure there are no problems. You may hear or feel the system working. This is normal and does not mean there is a problem with your vehicle. If driving conditions delay system initialization, the STABILITRAK NOT READY message may be displayed. If this is the case, your vehicle does not need servicing.
When the StabiliTrak system is both on and actively controlling the stability of the vehicle, the StabiliTrak light will blink for the duration of the event.
You may also feel or hear the system working. This is normal.
StabiliTrak will turn off automatically if a problem is detected in the system. The StabiliTrak light will come on and SERVICE STABILITRAK will be displayed on the DIC. For vehicles without a DIC, the StabiliTrak light and the StabiliTrak service light will both come on. If the SERVICE STABILITRAK message (or StabiliTrak service light) does not clear itself after restarting the vehicle, you should see your dealer for service.
Not finding what you are looking for?

434 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...