Question about 2000 Jeep Grand Cherokee

1 Answer

Ac blower won't work. Resistor has been replaced 3 times. I think it is the problem now. Is it easy to replace? Where is it?

Where is the blower motor resistor for the ac. Is it hard to replace? 2000 jeep grand cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 710 Answers

Blower motor resistors are found on the pasenger side ducts near the blower motor. It should have three wires going to it.

Posted on Apr 22, 2009

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blower does not work on 2000 grand cherokee jeep


check burn fuse first and if ok check blower motor resistor

Mar 03, 2015 | 2000 Jeep Grand Cherokee

1 Answer

How to change blower motor in. 99 grand Cherokee


Check this procedure...Blower Motor Resistor and Controller Replacement


REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.


INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

zjlimited_1958.jpg


Hope this helps (rerember to rating this and leave a testiomonial).

Sep 30, 2011 | 1999 Jeep Grand Cherokee

1 Answer

I just had the a/c worked on my 2000 jeep grand cherokee. I replaced both the evaporator and the other hose as well. The a/c was working great. That night I went to town and the fan stops blowing?


Take the blower motor out, power it and if it works then change the blower motor resistor. If the motor dosent work when powered then change the motor.

Aug 25, 2011 | 2000 Jeep Grand Cherokee

1 Answer

How do i change blower motor resistor on 99 jeep grand cherokee


Welcome to FIxYa.com



Blower Motor Resistor and Controller Replacement

Image Blower Motor Resistor Or Controller/Power Module Remove/Install

REMOVAL

1. Disconnect and isolate the batten' negative cable.

2. Depress locking tab and unplug the wire harness connector from the blower motor

resistor or controller (power module).

3. Depress locking tab and unplug the resistor or controller connector from the blower

motor.

4. Remove the 2 screws that secure the blower motor resistor or controller to the

heater-AC housing.

5. Remove the blower motor resistor or controller from the heater AC housing.

INSTALLATION

1. Install the blower motor resistor or controller to the heater AC housing. The

housing is indexed to allow (controller power module) mounting in only one

position. Tighten the mounting screws to 2.2 Nm(20 in. Lbs.).

2. Plug in the wire harness connector to the blower motor resistor or controller.

3. Plug in the connector from the blower motor resistor or controller to the blower

motor.

4. Connect the batten' negative cable.

leedavidian_45.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Nov 22, 2010 | 1999 Jeep Grand Cherokee

1 Answer

T he blower motor only works in the hi position , i believe i need a new resistor, where exactly is it located ? on the blower motor itself and inside the vehicle? do i need to tahe the blower motor out?


I have a 2000 jeep grand cherokee and recently had the same problem...only I actually replaced my blower motor before I found that it wasnt the issue. The blower motor resistor is located on the passenger side under/behind the glove box. It will have 2 screws in it and a wiring harness coming out of it. Very easy to replace. Cost is about 115-145 depending on where you buy.

Jan 20, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Blower motor resistor replacement


how do the wires go on a 2002 jeep grand cherokee blower motor resister.

Oct 18, 2009 | 2002 Jeep Grand Cherokee

2 Answers

1994 jeep grand cherokee heater only works on high


U need to replace the blower motor speed control resistor.

Feb 25, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Heater Air Motor not working on 2000 Jeep Grand Cherokee all the controles seem to work they light up and change when you turn the knob but no motor movment tried looking for the fuse but could not find


First off, it's called the blower motor. Check in your manual for the fuse for that. If the fuse is good, it could either be a bad blower motor or blower motor resistor.

Sep 10, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

864 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...