Rear anti lock

You need a mechanic with a high level scan tool to check the Diagnostic Trouble Codes and Live Data. It is probably ABS Sensor related, but should never leave you with no brakes..

The most common problem?!?!?!
FORD!!!!!!!!!!!!!!!!!!!!!
Next time you have occasion to pull the instrument cluster. I suggest you remove that pesky bulb and be done with it! That "anti -lock" system was a joke anyway. Who puts "anti-lock" on the REAR??????????
They really didn't think this through did they!
Oh and just one more little pet peeve of mine.
ALL FULL SIZE BRONCOS ARE 4X4!!!!!!!!!!!!!
AND ALL FULL SIZE TOPS COME OFF TOO!!!!!!!

YOU HAVE A BAD MASTER CILINDER REPLACE IT ITS BAD ANY MORE QUESTIONS LET ME KNOW OK

Pull the codes.

there is actually a trick that works most times, when you go to bleed the rear turn the key to on, the pump will allow the fluid out to the rear.

The torque setting 49 ft. lbs.


Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

NO CK FOR WIRES BROKEN TO ABS SENSOR ON TOP OF THE REAR TWO WIRE TERN. & CK SENSOR IN REAR WITH OM METER

here is a 96 taurus


Item Part Number Description 1 2C296 Anti-Lock Brake Tube 2 2C219 Anti-Lock Brake Module 3 2005 Power Brake Booster 4 2263 Front Brake Tube 5 2B091 Brake Pressure Control Valve 6 2140 Brake Master Cylinder 7 2B547 Brake Load Sensor Proportioning Valve 8 N802191-S60 Bolt 9 2L568 RH Rear Brake Tube 10 2L569 LH Rear Brake Tube 11 2C287 Brake Fluid Distributor Tube 12 N808531-S301 Bolt 13 — Front Side Member 14 N802324-S56 Bolt 15 18124 Front Shock Absorber 16 2B121 Front Disc Brake Caliper 17 2078 Front Brake Hose 18 2264 Front Brake Tube 19 2553 Rear Disc Brake Caliper 20 2A442 Rear Wheel Brake Hose 21 N808728-S60 Bolt 22 — Side Rail 23 N802324-S60 Bolt
Brake Load Sensor Proportioning Valve


Item Part Number Description 1 2B547 Brake Load Sensor Proportioning Valve 2 — Body 3 N802191-S56 Bolt (2 Req'd) 4 2L568 Brake Tube Assy 5 2L569 Brake Tube Assy 6 2265 Brake Tube Assy 7 2B255 Brake Tube Assy 8 5500 Rear Suspension Arm and Bushing 9 W611634-S301 Bolt A — Tighten to 11.4-15.6 Nm
(8-12 Lb-Ft) B — Tighten to 10-14 Nm (7-10 Lb-Ft)

Brake Hose, Rear —Drum


Item Part Number Description 1 — Rear Side Rail 2 2L569 Rear Brake Tube 3 N602324-S60 Screw 4 N611193-S60 Screw 5 2C023 Left Hand Rear Hose and Connector 6 2210 Rear Drum Brake Backing Plate 7 18125 Rear Shock Absorber 8 2267 Rear Brake Tube A — Tighten to 16-20 Nm (12-15 Lb-Ft)

metal particles on the trigger wheel sensor of the rear differential case, this causes a loose of signal and the light to come on. also a broken tooth on the trigger wheel inside the diff can cause this or a dirty/corroded connection to the sensor from water intrusion.

This isn't hard to do at all really and should be easy to procure the part from the local parts store. There is only one little screw holding it in

1. Raise and support vehicle.
2. 
   NOTE: Clean off dirt and foreign material that may have collected around the rear anti-lock brake sensor before removal. Remove the rear anti-lock brake sensor.

1 Disconnect the rear anti-lock brake sensor electrical connector. 2 Remove the bolt. 3 Remove the rear anti-lock brake sensor.

1. NOTE: Thoroughly clean the mounting surface. NOTE: Inspect the anti-lock brake sensor O-ring for damage; lightly lubricate the O-ring with axle lubricant. To install, reverse the removal procedure