Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Oct 29, 2013

How do i bypass mass air flow sensor on a 2008 5.3 lieter gmc sierra

5 Related Answers

Anonymous

  • 566 Answers
  • Posted on Dec 20, 2008

SOURCE: Where is the mass air flow sensor located on a jaguar x-type

hi from the uk the location of mass air flow sensor on x type jag is as follows==it is on the r/h/side of the air filter cover with jaguar embossed on top? this sensor is just prior to the intake hose that connects to the motorised throttle body from filter connections underneath it to unplug and meter is held by two screws ?if memory serves ? may i suggest you remove the large hose and use a little wd40 or similar to clean /lubricate the throttle butterfly in throttle body throat at this point so as to prevent future sticking upsetting of idling ? hope this helps ?

Ad

Anonymous

  • 39 Answers
  • Posted on Apr 02, 2009

SOURCE: mass air flow sensor bad on 2002 monte carlo ss

It's should be a simple remove and replace. Just make sure the engine is off. Also do not touch any of the filament wires on the sensor, just the plastic housing. Also after you install it drive the car for a little while (city speeds, cruising speeds and inbetween). That way the computer will be able to readjust its setting since it is a new sensor.

Anonymous

  • 66 Answers
  • Posted on May 06, 2009

SOURCE: mass air flow sensor

maf sensors identify the amount of air flow flowing in the intake. the sensor works with the throttle so it knows how much air is coming in to add the proper amount of fuel to mix with the air. Easy to pull and replace.

Anonymous

  • 15935 Answers
  • Posted on Sep 04, 2009

SOURCE: location of mass air flow sensor

The sensor is mounted on the throttle body between the air cleaner assembly and the air cleaner outlet tube.

4641370.jpg
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

brentfelz

  • 5 Answers
  • Posted on Oct 09, 2009

SOURCE: looking to findthe mass air flow sensor on a 89 chevy corsica

location is under the hood where the aircleaner is there is an electrical connection that plugs into the mass air flow sensor

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I got a 1999 GMC Sierra 4.8 l engine four-wheel drive when I plug in the massive air flow sensor it kills my truck

The sensor or it's wiring are bad . Check for corossion or wire damage first . Mass air flow sensors are most affordable through Rock Auto online .
0helpful
1answer

1996 gmc sierra 5.7L what would cause engine codes p0102, p0108, p0121,p0300 at same time?

p0102 is MAF mass air flow , circuit low input. Try these to reset code by trying following.
Verify that the Mass Air Flow Sensor wiring is connected properly and that there are no broken / frayed wires. Inspect for any air leaks near the MAF sensor. Take the MAF out and clean it using a spray cleaner such as brake cleaner or electrical contact cleaner. Be gentle with the sensor. Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information) Replace the MAF sensor.
P0121 Throttle Position Sensor/Switch A Circuit Range/Performance Problem
P0108 EGR Barometric Pressure Sensor Input Signal is out of self test Range. P0300 Random Misfire Detected.
0helpful
1answer

1997 gmc sierra fix the code po102

code po102 refers to mass air flow(MAF) sensor/volume air flow (VAF) sensor---low input======causes --wiring short to ground---MAF/VAF sensor ---ECM
0helpful
1answer

I have a 2002 GMC Sierra 1500. 4.3 liter engine. I brought it to autozone and they put the gauge on it and got two codes P0140 and P0300. I had my distributor cap replaced, ignition rotor, plugs ,wires,...

Clean mass air flow sensor with a nonchlronated brake cleaner,install new air filter and check all vacuum lines for leaks then check for vacuum leak around or at intake manifold.Code P0140 is for mass air flow sensor code P0300 is a multiple misfire which more than likely is a vacuum leak possibly intake manifold gaskets leaking.
1helpful
2answers

1998 GMC Sierra 2500 5.7L hard cold starts last month, now won't start cold w/o a little carb cleaner in intake. Codes for oxy sensors, mass air sensor and crank/cam position. Drove today, no power just...

starting definately has a lot to do with the crank/cam position sensors, but it wouldnt have nothing to do with hot or cold weather, oxygen sensor will make the vehicle run too rich if its out, you will smell fuel very strong out the exhaust, that could make it run sluggish also, and usually if the mass air flow sensor goes out the vehicle wont start at all...
1helpful
1answer

Where is the mass flow sensor located?

open hood, passenger side of car, right past the air cleaner is a tube (snorkel) MASS AIR FLOW SENSOR going with 4 wires going into it,
that should be it! thanks 4 inquiring
3helpful
1answer

2000 gmc starts but then idles rough then dies

I had to replace the mass air flow sensor. $ 150. the engine would shut off when driving too.changed fuel filter only worked for a day. The sensor is just after air filter.
0helpful
1answer

Mass air sensor and intake air temperature sensor

They are not the same thing but the air temp sensor is made into the mass air sensor
Not finding what you are looking for?

491 views

Ask a Question

Usually answered in minutes!

Top GMC Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...